Echo BEAR CAT SC5720B Скачать руководство пользователя страница 22

Страница: 22 / 30

5 INCH CHIPPER/SHREDDER/BLOWER

SERVICE & MAINTENANCE

BEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE,

AND MAKE SURE ALL MOVING PARTS HAVE COME TO A COMPLETE STOP.

WARNING

If the machine becomes plugged, shut off the engine,

disconnect the spark plug wire and allow the machine

to come to a complete stop before clearing debris.

Do not operate machine without proper guards and

screens in place.

WARNING

5.9 CLEARING A PLUGGED ROTOR

Stop engine, disengage rotor clutch and allow machine

to come to a complete stop. Remove the spark plug

wire.

Loosen and remove the 3/8” carriage bolts securing

the chipper access cover.

Open the knife access cover, exposing the chipper

shredder compartment.

5.10 REMOVING THE ROTOR

Loosen and remove the 3/8” carriage bolt securing the

knife access cover.

Open the access cover, exposing the chipper shredder

compartment.

Loosen the bushing bolts holding the drive pulley to the

shaft and remove the pulley.

Loosen the set screw in the lock collars. Using a punch

and hammer, tap the lock collars in a direction opposite

of normal rotation so that they can be removed.

Unbolt bearings and lift rotor out of machine.

Remove bearings from rotor shaft.

Re-install rotor assembly and bearings and tighten bolts

to proper torque.

5.11 REPLACING THE DRIVE BELT

Stop engine, disengage rotor clutch and allow machine

to come to a complete stop. Remove the spark plug

wire.

Place the engagement handle in the START position.

Remove the 5/16 x 3/4" bolts and washers securing

the shields in place and remove shields.

Figure 5.7, Drive belt on rotor pulley

Figure 5.6, Rotor access

Figure 5.7, Rotor access

Check the condition of the drive belt annually or after every

25 hours of operation, whichever comes first. If the belt is

cracked, worn, frayed, or stretched, replace it. To replace

the belt:

Clean the debris out of the shredding rotor and/or

chipper top discharge area and tube. Turn the rotor by

hand to be sure it is free to rotate.

Replace spark plug wire, restart engine and resume

operation.

Содержание BEAR CAT SC5720B































Результаты поиска

Содержание BEAR CAT SC5720B

Отзывы:

Похожие инструкции для BEAR CAT SC5720B

Бренды по названию

Популярные бренды

Echo BEAR CAT SC5720B, Руководство пользователя

Результаты поиска

Содержание BEAR CAT SC5720B

Отзывы:

Похожие инструкции для BEAR CAT SC5720B

Бренды по названию

Популярные бренды