Ecco Axios страница 38 Скачать руководство пользователя

Страница: 38 / 40

MANUFACTURER LIMITED WARRANTY & LIMITATION OF LIABILITY

Manufacturer warrants that on the date of purchase this product

will conform to Manufacturer’s specifications for this product

(which are available from the Manufacturer upon request). This

Limited Warranty extends for Sixty (60) months from the date of

purchase.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING,

ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED

MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER

INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED

IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET

FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING

INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.

Exclusion of Other Warranties:

MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR

IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY,

QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING

FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE

HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT AND

ARE HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED

BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS

ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.

Remedies and Limitation of Liability:

MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE

REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE),

OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER

REGARDING THE PRODUCT AND ITS USE SHALL BE, AT

MANUFACTURER’S DISCRETION, THE REPLACEMENT OR REPAIR

OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE

PAID BY BUYER FOR NON-CONFORMING PRODUCT. IN NO

EVENT SHALL MANUFACTURER’S LIABILITY ARISING OUT OF

THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO

THE MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID

FOR THE PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL

PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR

LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR,

PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR

INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH

OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR

OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S

REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER

OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT OR

ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER

ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER

OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty defines specific legal rights. You may have

other legal rights which vary from jurisdiction to jurisdiction.

Some jurisdictions do not allow the exclusion or limitation of

incidental or consequential damages.

NOTE

Operating the vehicle without the outer lens installed on the

product may result in damage that will NOT be covered under

the warranty.

Содержание Axios









































Результаты поиска

Содержание Axios

Отзывы:

Похожие инструкции для Axios

Бренды по названию

Популярные бренды

Ecco Axios, Руководство пользователя

Результаты поиска

Содержание Axios

Отзывы:

Похожие инструкции для Axios

Бренды по названию

Популярные бренды