Ecco Axios страница 36 Скачать руководство пользователя | Manualshive

Страница: 36 / 40

background image

36

AXIOS

™

TROUBLESHOOTING

Should you encounter a problem during installation or during the life of the product, follow the guide below for troubleshooting
and repair information. If the problem cannot be rectified using the solutions given below, additional information may be
obtained from the manufacturer – contact details are at the end of this document.

LIGHTBAR & CONTROLLER

Problem

Possible Cause

Solution

Does not function

Poor power or ground connection

Check fuse, cables, and connections to the

lightbar and to the controller. If fuse is

blown, check wiring and replace fuse. If

problems persist replace the controller with

good unit. If problem continues, contact

your Axios distributor, or the manufacturer

for warranty repair or replacement (contact

information on page 37).

Blown fuse

Check wiring, replace fuse.

One or two LED modules do not flash, but

Pattern 1 or Pattern 2 indicator LED on

controller is on

Open circuit wiring from central control

board to LED module

Verify the correct installation of the

modules in the power rail, if problem

persists, replace the modules. If all modules

installed within a section of power rail (i.e.

front left) are inoperable and are installed

correctly, contact your Axios distributor, or

the manufacturer for warranty repair or

replacement (contact information on page

37).

Failed LED module

LED modules flashes dimly

Defective module or central control board

If only one module is dim, replace it. If all

modules are dim, verify that lighbar voltage

is greater than 11V.

Incorrect flash patterns

Wrong flash configuration

Re-program flash pattern presets 1, 2 and 3.

«
...
34
35
36
37
38
...
»

Содержание Axios









































Отзывы:

Нет отзывов

Похожие инструкции для Axios

Бренд: ABB Страницы: 86

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Rath Страницы: 3

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

Бренд: Garelick Страницы: 2

Бренд: Garelick Страницы: 2

Бренд: Gardigo Страницы: 32

Бренд: Ultraflex Страницы: 3

Бренд: Sagola Страницы: 62

Бренд: Tanaka Страницы: 20

Бренд: Tandem Страницы: 80

Бренд: Tanco Страницы: 4

Бренд: V.ORLANDI Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды