background image

 

14 

1 5

P

P

P

P

1 5

P

P

P

P

,

 

(4)   

How to DELETE all pin codes of all the users 

 

In program mode, press  

  

The letters P P P P represent the password,  
You must press and hold the hash key # at the end of the command for three seconds until you hear the system 
say:  

The pin code was deleted

 “

  

 

 

By SMS message: 

To DELETE all pin codes of all the users by SMS command, send the following message:    
 

 

 
 

 
 
 
 
 

 
 
(C)  How to set the unit to FACTORY DEFUALT settings 

There are two ways to set the units to factory settings, by the keypad or by SMS command.  

 

1.   By keypad 

Enter **00*# and press and hold the # key for 3 seconds till you hear a long beep.  
Enter **00*# once again (within 10 seconds) and the unit will respond with a long beep and announce 
“Delete” after 10 seconds.  If you do not enter **00*# the second time within 10 seconds, the unit will 
disregard the command and exit that mode. 

 

2.  By SMS: 

Send SMS command as follows:

 PPPP**00*#,PPPP**00*# 

 
The system will send back SMS message as:  

PPPP**00*#, PPPP**00*#   CONFIRMED.  

 
 
 
 
 

 

©All Rights Reserved to  

ECA Electronic Engineering Pty. LTD. 

AUSTRALIA 

Tel: +61 3 95720535

 

[email protected] 

www.gatesonsolar.com

 

Warning ! 

Setting the unit to FACTORY DEFALT will delete all phone numbers, 

pin-codes and set all the parameters of the unit to the factory Settings. 

 

Содержание MCI-3000V4















Отзывы: