background image

 

11 

1 1

1 1

P

P

P

P

1 2

1 2

P

P

P

P

N

1 3

N

1 3

P

P

P

P

10. 

How to check the next available empty memory in the system

   

 

 

 

Via the keypad, in program mode, press  

The unit will 

announce the next empty memory position by saying individual numbers;  

i.e. If the next empty memory cell is “ 0 2 6 ” the system will say: Zero, Two, Six     

 

 

In order to get the next available empty memory position in the system by SMS command,  

          send SMS as follows:   

 

                                                     PPPP 

represent the 4 digit PASSWORD.   

 

The unit will send SMS reply to the sender that says:

 “ The nest available position is X X X “    

The letters X X X represent three digit number (such as 055) to indicate the empty memory position.     

 
 

11.  

How to check the GSM reception level in the unit’s location area

 

 

The unit is able to provide the reception level in the area by the following command in program mode: 
 
 
The unit will announce the level by a number from 0 to 5 according to the table below: 
 

Zero -  No Reception  
One  -  Bad reception  
Two -  Poor Reception 

Three -  Good reception  
Four  -  Very Good reception 
Five   -  Excelant Reception.  

 

By SMS Command  

The unit will send SMS replay with the GSM reception level when the following SMS command is 
sent: 

 

 

 

 

The unit will reply with SMS message:  

“The reception level is X “ 

The letter 

“ X”  represents a number from  “0“  to  “ 5“.  

 

 

12.  

OPEN TO ALL command

 

 

The unit can be programmed so that it will open the gate to ANY phone call received without checking the 
phone number calling.  
You can activate or cancel this feature in program mode as follows: 
 
Enter program mode Via the keypad and press:    
“ N “ represents the numbers “1” or “2”   
The number “1” to activate “OPEN TO ALL” feature.  
The number “2” to “CANCEL” this feature.    
The unit will confirm by long BEEP.  

 
By SMS Command  

You can also send SMS to activate or cancel this feature as follows:  
 
 
The unit will replay by the following SMS to the sender saying:    

“ Open to all is activated ”  or   “Open to all is canceled”.

 

 

   

Содержание MCI-3000V4















Отзывы: