7
Instruction Booklet
IB02601014E
Effective December 2012
Enclosed meter—
PXM 4000/6000/8000
eaton Corporation
www.eaton.com
S1 LED
Meter Test LED (Follows state of S1)
S1 Solid State
Form A Output
S2 Solid State
Form A Output
Max. Load: 100 mA
Max. Voltage: 30V
R1 Form C Relay Output
R1A Normally Open/R1B Normally Closed
R2 Form C Relay Output
R2A Normally Open/R2B Normally Closed
R3 Form C Relay Output
R3A Normally Open/R3B Normally Closed
240 Vac
30 Vdc
Max. 5A
DI1–DI8
Discrete Inputs
Self Sourced: 24 Vdc ~10 mA/Input
24 Vdc Internal Source
DIS
Discrete Input Source
6
PXMIO-B
5A 240VA
C
3
0
V
D
C
9
8
7
S
ELF
S
O
U
RC
E
2
4V
D
C
5
4
3
2
IO3
-
1
100m
A
3
0V
D
C
4
IO2
-
3
2
1
6
9
8
7
5
3
4
1
IO1
-
2
R2B
R3B
R3C
R3A
R2A
R2C
R1B
R1C
S21
R1A
S22
S12
S11
DI6
DIS
DI8
DI7
DI5
DI4
DI3
DI1
DI2
CW
S1 LED
10VA Source MAX
PXCM-5
TXD
RXD
C
24+
SH
SH
DB
DA
C
M6-
3
2
1
C
M5-
3
2
1
Com 0 Display
10VA Source MAX
C
24+
SH
C
M4-
3
2
1
Com 1 RS485
TXD
RXD
SH
DB
DA
C
M3-
3
2
1
RXD/TXD
10/100 T (RJ45)
Local Configuration
Link
CM
1
CW
C
E
4
PXCE-B
100 Fx (ST)
LAN/WAN
10/100 T (RJ45)
TXD/RXD
Com 2 RS485
Link
Com 3 RS232
1
CE3-
2
3
DA
RXD
TXD
DTE
TXD RXD
SH
DB
CE
2
Tx
CE
1-
Rx
CW
P
S
1-
100-240VAC
PXPS-1
110-250VDC
50W Max
47-63 Hz
2
1
(+) L
(-) N
Rating
DO NOT HIPOT / DIELECTRIC TEST
AVERTISSEMENT: CET EQUIPEMENT RENFERME PLUSIEURS
REMOVE POWER BEFORE SERVICING
3
G
CIRCUITS SOUS TENSION. VOIR LE SCHEMA.
MORE THAN ONE LIVE CIRCUIT. SEE DIAGRAM.
WARNING
CW
for technical support
1-800-809-2772 or 1-414-449-7100
www.EatonElectrical.com
Customer Satisfaction
<http://www.EatonElectrical.com
2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
E185559
MEASURING EQUIPMENT
20NL
Pertains to Models PXM 4000/6000/8000
with Option B in Card Slot 3
Figure 4. PXM 4000/6000/8000, 8 Digital Inputs, 2 Solid-State
Outputs, 3 Relay Outputs
The RJ45 jack has embedded LEDs as before but the
functionality is different:
• 100—Port speed, Green LED will light at
100 base Tx or out at 10 base T.
• Link—Green LED will Blink when it detects
Rx/Tx Ethernet communication activity.
A new 4 element LED indicator is added below the RJ45 connector
S1—Status 1—Lit when the port is down.
S2—Status 2—Lit when comm. reset in process.
10—Lit when IP address other than 192.168.1.1 is active.
TA—Transmit Active.
CM3—COM1—3 terminal plug RS485 interface configurable as
Modbus RTU Slave or Gateway Master/Slave. Defaults to slave
Gateway.
• CM31 Data A (–)
• CM32 Data B (+
• CM33 Shield (RS485 common) )
CM4—24 Vdc 10W max.—3 terminal, gender inverted plug.
Source for use with auxiliary devices. (See following pages
for further details.)
NOTE: This output is electrically common with
CM3/COM1. Do not extend cable beyond 30M.
• CM41 Shield
• CM42 24V+
CM5—COM0—RS485 dedicated to remote Display interface for
connection to DG1/COM0 of the Display. The Meter address is
assigned using the Rotary Switch found below the meter left side
CT terminal.
• CM51 Data A (–)
• CM52 Data B (+)
• CM53 Shield (RS485 common)
CM6—24 Vdc 10W max.—Used to power the Graphical Display
if the cable distance is less than 30M. If greater than 30M, use a
separate 24V supply to power the Display.
• CM61 Shield
• CM62 24V+
• CM63 24V common
Future Expansion
Figure 5. PXM 4000/6000/8000, RS-485 Output
