Eaton Power Xpert XGIS Скачать руководство пользователя страница 7

Страница: 7 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Section 1: Introduction

1.1 Preliminary comments and safety precautions

This technical document is intended to cover most aspects

associated with the installation and commissioning of Power

Xpert

XGIS gas insulated switchgear. It is provided as a guide

for authorized and qualified personnel only. Please refer to the

specific WARNING messages in paragraph 1.1.2 before proceeding

past Section 1. If further information is required regarding a

particular installation, application or maintenance activity, an Eaton

representative should be contacted.

1.1.1 Safety precautions

All safety codes, safety standards and/or regulations must be strictly

observed in the installation, operation and maintenance of this

device.

WARNING

THE WARNINGS AND CAUTIONS INCLUDED AS PART OF THE

PROCEDURAL STEPS IN THIS DOCUMENT ARE FOR PERSONNEL SAFETY

AND PROTECTION OF EQUIPMENT FROM DAMAGE. AN EXAMPLE OF A

TYPICAL WARNING LABEL HEADING IS SHOWN ABOVE TO FAMILIARIZE

PERSONNEL WITH THE STYLE OF PRESENTATION. THIS WILL HELP TO

ENSURE THAT PERSONNEL ARE ALERT TO WARNINGS, WHICH MAY

APPEAR THROUGHOUT THE DOCUMENT. IN ADDITION, CAUTIONS ARE ALL

UPPER CASE AND BOLDFACE AS SHOWN BELOW.

WARNING

COMPLETELY READ AND UNDERSTAND THE MATERIAL PRESENTED IN

THIS DOCUMENT BEFORE ATTEMPTING INSTALLATION, OPERATION

OR APPLICATION OF THE EQUIPMENT. IN ADDITION, ONLY QUALIFIED

PERSONS SHOULD BE PERMITTED TO PERFORM ANY WORK ASSOCIATED

WITH THE EQUIPMENT. ANY WIRING INSTRUCTIONS PRESENTED IN THIS

DOCUMENT MUST BE FOLLOWED PRECISELY. FAILURE TO DO SO COULD

CAUSE PERMANENT EQUIPMENT DAMAGE, BODILY INJURY OR DEATH.

WARNING

THE POWER XPERT XGIS SWITCHGEAR DESCRIBED IN THIS DOCUMENT

ARE DESIGNED AND TESTED TO OPERATE WITHIN ITS NAMEPLATE

RATINGS. OPERATION OUTSIDE OF THESE RATINGS MAY CAUSE THE

EQUIPMENT TO FAIL, RESULTING IN DEATH, BODILY INJURY AND

PROPERTY DAMAGE.

ALL SAFETY CODES, SAFETY STANDARDS AND/OR REGULATIONS AS

THEY MAY BE APPLIED TO THIS TYPE OF EQUIPMENT MUST BE STRICTLY

ADHERED TO.

1.1.2 Switchgear identification

A nameplate is located on the exterior door of each XGIS switchgear

vertical section. Contained on this nameplate are the general order

number, manufacturing shop order number, and all the necessary

switchgear ratings. This information should be given to the Eaton

sales office if a question should arise concerning the switchgear or if

renewal parts are required. This information is sufficient for Eaton to

find the manufacturing information for the switchgear.

Содержание Power Xpert XGIS

















































































Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды

Eaton Power Xpert XGIS, Инструкция пользователя

Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды