Eaton Power Xpert XGIS Скачать руководство пользователя страница 13

Страница: 13 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Figure 8.

Tank viewing port.

The camera port provides a view of all three of the 3PDS

mechanisms, and shows the ground, open and closed positions

and armature poles.

Figure 6

shows view port images of all three

disconnect switch poles.

Figure 9.

3PDS pole positions viewed at port. Images are

enhanced for clarity.

Circuit breaker cycle counter
The 1250 A XGIS circuit breaker is rated for 10,000 load or no-load

operations. The 2000 A and 2500 A XGIS circuit breakers are rated

for 2,000 load or no load operations. Each closing spring charging

operation is recorded on the cycle counter mounted on the left side

of the circuit breaker frame, and viewable through a window in the

front cover.

Figure 10. Circuit breaker cycle counter.

1.3.1.2 Medium-voltage area

SSIS conductor system
Power input and output circuits between XGIS vertical sections are

connected to the XGIS using shielded solid insulation system (SSIS)

conductor and termination elements. These elements are designed

for medium voltage application and provide excellent insulation and

current carrying features when properly installed using their mating

bus joints.

Figure 11. Main bus joint cones (SSIS).

The outer layer of each insulating component of the SSIS conductor

system is shielded and grounded to the tank. The entire exterior of

the SSIS conductor is at ground potential when properly installed.

Gas tank
Behind the low-voltage panel and above the output cable

compartment, the gas tank is the heart of the XGIS switchgear. The

tank is pressurized to slightly over atmospheric pressure with SF

gas, to insulate the MV components inside the tank.

Содержание Power Xpert XGIS

















































































Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды

Eaton Power Xpert XGIS, Инструкция пользователя

Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды