Eaton Power Xpert XGIS Скачать руководство пользователя страница 37

Страница: 37 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Section 2: Safe practices

2.1 Recommendations

Type XGIS vacuum circuit breaker elements are equipped with high

speed operating mechanisms. They are designed with several built-in

interlocks and safety features to provide safe and proper operating

sequences.

WARNING

TO PROTECT PERSONNEL ASSOCIATED WITH INSTALLATION, OPERATION,

AND MAINTENANCE OF THESE SWITCHGEAR ELEMENTS, THE FOLLOWING

PRACTICES MUST BE FOLLOWED:

•

Only qualified persons, as defined in the local electrical code, who

are familiar with the installation and maintenance of medium-

voltage circuits and equipment, should be permitted to work on

switchgear.

•

Read these instructions carefully before attempting installation or

commissioning of this equipment.

•

Do not work on a closed breaker or a breaker with closing springs

charged. The closing spring should be discharged and the main

contacts opened before working on the breaker. Failure to do so

could result in injuries.

•

Do not use a circuit breaker by itself as the sole means of

isolating a high voltage circuit. Open the 3PDS and follow

good lockout and tagging rules, as well as all applicable codes,

regulations and work rules.

•

XGIS switchgear employs sulfur hexafluoride (SF

) in the

enclosure tank, at slightly higher than nominal atmospheric

pressure. Special precautions must be followed if service is

required on the SF

tank.

•

is heavier than air and will displace air in a confined space.

This can present a suffocation hazard.

•

Never allow only one person access to the XGIS tank to perform

maintenance or service work.

•

Always replace the tank desiccant after performing tank

maintenance.

•

Once XGIS tank service is completed, personnel must clean their

hands, faces and exposed skin immediately. Tools and PPE must

also be cleaned.

•

MUST NOT be discharged into the atmosphere. It should be

collected and may be reused only after treatment and testing by

qualified experts.

Содержание Power Xpert XGIS

















































































Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Бренды по названию

Популярные бренды

Eaton Power Xpert XGIS, Инструкция пользователя

Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Бренды по названию

Популярные бренды