Eaton Power Xpert XGIS Скачать руководство пользователя страница 26

Страница: 26 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

1.3.6.1 Feeder/incoming

The feeder/incoming vertical section includes both the 3PDS and

the vacuum interrupter circuit breaker. It includes SSIS main bus and

cable connections. This section can be furnished with fused VTs with

a disconnect switch, cable CTs, remote-mounted fused VTs or surge

arresters.

Figure 52. Feeder/incoming one-line.

1.3.6.2 Bus tie

The bus tie vertical section includes both the 3PDS and the vacuum

circuit breaker. It is intended to connect two separate buses. It can

be furnished with a set of VTs with the VT earthing switch and bus

CTs.

Figure 53. Bus tie one-line.

Содержание Power Xpert XGIS

















































































Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды

Eaton Power Xpert XGIS, Инструкция пользователя

Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды