Eaton Power Xpert XGIS Скачать руководство пользователя страница 64

Страница: 64 / 80

Instruction Booklet

IB022018EN

Effective July 2020

Instructions for the installation and

commissioning of Power Xpert

XGIS gas insulated switchgear

EATON

www.eaton.com

Figure 113. VT front lift final position.

DANGER

ENERGIZED PARTS WILL CAUSE SERIOUS INJURY OR DEATH. DO NOT

CONNECT A PLUG-IN TYPE VOLTAGE TRANSFORMER WHILE THE XGIS

SWITCHGEAR IS ENERGIZED.

BEFORE INSTALLING OR REMOVING THE VOLTAGE TRANSFORMER, CUT

POWER TO THE RELEVANT BUSES AND GROUND THEM ACCORDING TO

REGULATIONS.

5.14.2 Voltage transformer installation

Top voltage transformer compartment mounted VTs (fused and

unfused)
Installing a top-mounted fused VT and its mounting bracket is

facilitated by the VT Installation/Removal tool, Eaton catalog number

87A1060G01

. Eaton will furnish one tool per XGIS lineup. This tool is

composed of three elements, and additional tools can be purchased

from Eaton or purchased from McMaster-Carr using the following

catalog numbers:

ote:

some applications will require that the VT mounting brackets be fitted

with fuse blocking plates to prevent access to the VT fuses without removing

the VT.

Figure 114.

Metal-Clad

Plug-in VT

(One per phase)

VT Lifting /

Mounting

Bracket

Fused VT

Mounting

Bracket

Brace

Fuse Blocking Plate

Welded to Mounting Bracket

(One per phase)

VT lifting / mounting brackets with fuse blocking

plates installed.

Table 13. Top VT installation tool components

Catalog
Number

Description

5522A39

3/8” square drive socket extension, 34 inches

7229A62

Magnet bit holder, 3/8” square drive, 1/4’ bit hex

shank

4309A16

Screw-holding 6 mm hex bit, 1/4”hex shank

One VT installation/removal tool set will be provided per lineup.

The voltage transformer is provided with a mounting bracket

installed. The mounting bracket also serves as an installation bracket.

Do not remove this bracket.

Figure 32

shows a fused bus VT with

its mounting bracket.
Voltage transformers are heavy - they can weigh as much as 165

lb. If it is necessary to install or remove a voltage transformer, care

must be taken to properly handle the voltage transformer in a safe

and secure manner.
Prepare the vertical section for VT installation

•

Remove the top sheet from the VT compartment. Loosen the VT

mounting bracket back brace to facilitate VT installation.

Figure

115

shows the VT bracket brace.

Voltage transformer lift truck
The VT lift truck comes in two designs to accommodate site ceiling

heights.
The high height design works best on sites where the control room

ceiling is high (see

Figure 74

), while the low height design works

best for low ceilings.
With the high lift truck, a VT can be installed from the front of a

vertical section. The low height design requires that the vertical

section side sheet be removed, and the VT installed from the side

for lateral access to the VT compartments.

Содержание Power Xpert XGIS

















































































Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды

Eaton Power Xpert XGIS, Инструкция пользователя

Результаты поиска

Содержание Power Xpert XGIS

Отзывы:

Похожие инструкции для Power Xpert XGIS

Бренды по названию

Популярные бренды