Eaton mMINT, Инструкция по установке и эксплуатации

Страница: 11 / 24

11
05/10 AWB1230-1622
Effective May 2010
mMINT—Modbus Translator Module—
installation and use
EATON CORPORATION www.moeller.net/en/support
Table 10. Primary Status Code Definitions
Code Definition
0 Unknown
1 Open
2 Closed
3 Tripped
4 Alarmed
5 On
Table 11. Secondary Status Code Definitions
Code Definition
3 Test mode
4 Disabled
7 Powered up
8 Alarm
Table 12. Cause of Status Code Definitions
Code Definition Code Definition
1 Normal operating mode 62 Short delay phase overcurrent
3 Instantaneous phase overcurrent 63 Fixed instantaneous phase
overcurrent #1
11 Overvoltage 64 Bad/missing rating plug
12 Undervoltage 65 Reverse power
13 Auxiliary overvoltage 66 Fixed instantaneous phase
overcurrent #2
14 Auxiliary undervoltage 67 Reverse phase
15 Underfrequency 68 Reverse sequence
16 Overfrequency 69 Phase current loss
17 Current unbalance 70 Phase voltage loss
18 Voltage unbalance 71 Alarm active
19 Apparent power factor 72 Bad frame
26 Power demand 73 Phase currents near pickup
27 VA demand 76 Fixed instantaneous phase
overcurrent #3
28 VAR demand 77 Set points error
29 Current demand 78 Overtemperature
30 Total harmonic distortion 79 Accessory bus
31 Operations count 80 Long delay neutral overcurrent
33 Control via communications 124 Zero speed
37 Coil supervision 125 Time between starts
39 Diagnostic warning #1 153 Operating mode service
40 Diagnostic failure #1 154 Mechanical error
41 Low battery 156 Extended position
42 Multiple causes 157 Shunt trip problem
61 Long delay phase overcurrent
Table 13. Control ‘Slave Action Number’ Definitions
Control Group Definition Byte2 Byte1 Byte0
Reset Reset trip 0 0 2
Reset (peak) demand-watts 0 0 4
Reset energy (kilowatt hours) 0 0 8
Reset (synchronize) demand
watts window
0 0 64 (40
16
)
Snapshot command 0 0 128 (80
16
)
Reset (peak) demand-currents 0 1 1
Reset all min./max. values 0 1 4
Unlock waveform buffer
(clear upload-in-progress)
0 1 5
Reset discrete input counters 0 1 6
Reset min./max. currents 0 1 13
Reset min./max. PF-apparent 0 1 16
0 1 17
0 4 X
Circuit breaker
open–close
Open request 1 0 0
Close request 1 0 1
Motor
start–stop
No action 2 0 0
Start fast forward 2 0 1
Start fast reverse 2 0 2
Stop 2 0 3
Start 2 0 4
Start slow forward 2 0 5
Start slow reverse 2 0 6
Set direction to forward 2 0 7
Set direction to reverse 2 0 8
Emergency override 2 0 10
Table 14. mMINT Configuration Registers
Register Definition R/W
Register
10
Modbus Address
16 No. of
Regs
10
Low High Low High
mMINT (247 or 248 addressed)
Invalid object access con-
figuration
R/W 42001 425345 07D0 6300 1
Floating Pt data word
order configuration
R/W 42002 425346 07D1 6301 1
Fixed Pt data word
order configuration
R/W 42003 425347 07D2 6302 1
INCOM (device addressed)
Mapped block of
registers configuration
R/W 41001 420481 03E8 5000 100
Mapped block of
registers data
R 41201 420737 04B0 5100 4 * 100
otee: N The register map for INCOM products is shown in register number
order in Table 8 and functional order in Table 9 . Numeric entries indicated
with an asterisk (*) have specific definitions dependent upon the particular
INCOM product .