background image

 

H-Max HVAC Drives

 

H-Max HVAC Drives

 

    MN04008004E—September 2011    www.eaton.com

 

i

 

Disclaimer of Warranties and Limitation of Liability 

 

The information, recommendations, descriptions, and safety notations in this document are 
based on Eaton Electrical Inc. and/or Eaton Corporation’s (“Eaton”) experience and judgment, 
and may not cover all contingencies. If further information is required, an Eaton sales office 
should be consulted. 

Sale of the product shown in this literature is subject to the terms and conditions outlined in 
appropriate Eaton selling policies or other contractual agreement between Eaton and the 
purchaser. 

THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, EXPRESSED OR 
IMPLIED, INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR 
MERCHANTABILITY, OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY EXISTING 
CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT STATES THE ENTIRE 
OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME 
PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be 
responsible to the purchaser or user in contract, in tort (including negligence), strict liability or 
otherwise for any special, indirect, incidental, or consequential damage or loss whatsoever, 
including but not limited to damage or loss of use of equipment, plant or power system, cost 
of capital, loss of power, additional expenses in the use of existing power facilities, or claims 
against the purchaser or user by its customers resulting from the use of the information, 
recommendations, and descriptions contained herein. 

The information contained in this manual is subject to change without notice. 

Cover Photo: Eaton H-Max HVAC Drives

Содержание H-Max Series





























Отзывы: