Eaton E5-648-C446 Series Скачать руководство пользователя страница 9

Страница: 9 / 24

Instruction leaflet

IL05407001E

Effective October 2010

E5-648-C446x electronic preset

counter with four presets (relays)

LCD negative, red-green backlighting

eaton corporation

www.eaton.com

Lock input

When the Lock input is activated

the programming is inhibited

When the Lock input is activated the

setting of the preset values is inhibited

When the Lock input is activated

the setting of the preset values and

the programming are both inhibited

7.8.5.2 Main menu for configuration

Main menu for matching the

input pulses and display

Multiplication factor

Multiplication factor can be programmed

from 00.0001 to 99.9999. The setting

00.0000 will not be accepted

Division factor

Division factor can be programmed from

01.0000 to 99.9999. The setting <01.0000

will not be accepted

Display mode

Calculation and display of the

frequency/speed in 1/s

Calculation and display of the

frequency/speed in 1/min

Decimal point setting

Decimal point (determines the resolution)

no decimal place

0.0

1 decimal place

0.00

2 decimal places

0.000

3 decimal places

Moving average

Moving average calculated

AVG 2: over 2 measurements

AVG 5: over 5 measurements

AVG 10: over 10 measurements

AVG 20: over 20 measurements

Start delay

Programmable from 00.0 to 99.9s

At the start of a measurement the

measurement results within this

time-period are ignored

Waiting time

Programmable from 00.1 to 99.9s

This value specifies how much time

should elapse, after the last valid edge,

before zero is to be displayed

Display color (for device E5-648-C446x)

Display color

Upper line: red

Lower line: red

Display color

Upper line: red

Lower line: green

7.8.5.3 Preset 1

See below 7.8.6.5

7.8.5.4 Preset 2

See below 7.8.6.6

7.8.5.5 Preset 3 and 4

See below 7.8.6.7

7.8.6 Timer

7.8.6.1 Main menu for Signal and Control inputs

Main menu for programming the signal and

control inputs

Input polarity

PNP: switching to Plus

for all inputs in common

nPn: switching to 0V

for all inputs in common

Filter for signal inputs Inp A and Inp B

For electronic control of the signal inputs

For mechanical control of the signal inputs

(for control with mechanical contacts)

Содержание E5-648-C446 Series

























Результаты поиска

Содержание E5-648-C446 Series

Отзывы:

Похожие инструкции для E5-648-C446 Series

Бренды по названию

Популярные бренды

Eaton E5-648-C446 Series, Инструкция

Результаты поиска

Содержание E5-648-C446 Series

Отзывы:

Похожие инструкции для E5-648-C446 Series

Бренды по названию

Популярные бренды