Eaton Cutler-Hammer Digitrip 520M Скачать руководство пользователя

Страница: 31 / 36

Effective 8/13/99

Page 31

I.L. 70C1037H02

Symptom

Probable Cause

Possible Solution(s)

References

Current thru breaker is <25%
of sensor rating.

No problem. Status LED will
not operate with breaker
currents <25% of sensor
rating.

Unit status LED is not
blinking.

Trip unit is malfunctioning.

Replace trip unit.

Light loading.

No problem. Status LED will
not flash until 25% of sensor
rating.

See Section 3.2 Note.

Unit status LED is steady on.

Trip unit is malfunctioning.

Replace trip unit.

Rating plug is not installed or
is loose.

Install rating plug and/or
check for loose connections.

Rating plug is open internally.

Replace rating plug.

As soon as current starts to
flow through the breaker, it
trips and the Instantaneous
trip LED comes on.

Trip unit is malfunctioning.

Replace trip unit.

Battery installed backwards.

Install correctly.

Dead battery.

Replace battery.

LED does not come on when
battery check button is
pressed.

Trip unit is malfunctioning.

Replace trip unit.

There actually is a ground
fault.

Find location of the fault.

On 4-wire residual systems,
the neutral current sensor
may not have the correct ratio
or be properly connected.

Check connections at
terminals B4 and B5. Check
that the neutral current sensor
ratio matches the breaker.
Check that the connections
from the neutral current
sensor to the breaker are not
reversed. Check B6, B7 for
correct programming of
jumper.

See Section 2.3, Notes.

Breaker trips on ground fault.

Trip unit is malfunctioning.

Replace trip unit.

Connection from Zout to Zin is
missing.

Make connections B8 to B9.

Refer to Appendix A.

Trip unit settings are not
correct.

Change settings.

Breaker trips too rapidly on
ground fault or short delay
(Zone Selective Interlocking
not used).

Trip unit is malfunctioning.

Replace trip unit.

Long Time Memory selected.

Turn off Long Time Memory.

Refer to Section 4.3.

Breaker trips too rapidly on
long delay.

Trip unit settings are not
correct.

Change settings. Long Time
Delay setting is based on
6

Ir.

Light load.

Check breaker ordering
information.

Refer to Section 1.6.1.

LCD display is not energized.

No auxiliary power input.

Check voltage input terminals
A14-A15.

Refer to Section 1.6.1.

Appendix B Troubleshooting Guide

Courtesy of NationalSwitchgear.com

Содержание Cutler-Hammer Digitrip 520M





































Результаты поиска

Содержание Cutler-Hammer Digitrip 520M

Отзывы:

Похожие инструкции для Cutler-Hammer Digitrip 520M

Бренды по названию

Популярные бренды

Eaton Cutler-Hammer Digitrip 520M, Инструкция по эксплуатации

Результаты поиска

Содержание Cutler-Hammer Digitrip 520M

Отзывы:

Похожие инструкции для Cutler-Hammer Digitrip 520M

Бренды по названию

Популярные бренды