Eaton Cutler-Hammer Digitrip 520M Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 36

background image

Effective 8/13/99

Page 25

I.L. 70C1037H02

CAUTION

BEFORE YOU FIT THE RATING PLUG INTO THE TRIP
UNIT, BE SURE TO CHECK THAT THE SENSOR
RATING MATCHES THAT PRINTED ON THE RATING
PLUG DOOR. INSTALLING A RATING PLUG THAT
DOES NOT MATCH THE SENSOR RATING CAN
PRODUCE SERIOUS MISCOORDINATION AND/OR
FAILURE OF THE PROTECTION SYSTEM.

NOTE: Rating plugs from Digitrip models 210, 500, or
510 CANNOT be used with DT20 Trip Units.

8.0 RECORD KEEPING

Use the forms shown in Figures 8.1 and 8.2 for record
keeping. Fill in these forms, giving the indicated reference
information and initial time-current trip function settings. If
desired, make a copy of the form and attach it to the
interior of the breaker cell door or another visible location.
Figure 8.3 provides a place for recording test data and
actual trip values.

Ideally, sheets of this type should be used and maintained
by those personnel in the user’s organization that have
the responsibility for protection equipment.

9.0 REFERENCES

9.1 Magnum and Magnum DS Circuit Breakers

I.B. 2C12060

Magnum DS Breaker Instructions

I.B. 2C13060

Magnum I. Breaker Instructions

4A36346

Zone Interlocking Application with Non-

Magnum Breakers

9.2 Time-Current Curves

The Time-Current Curves are listed below for particular
trip unit models. All protection function time-current
settings should be made following the recommendations
of the specifying engineer in charge of the installation.

70C1009

Digitrip 220 (LI) Curve

70C1006

Digitrip 520 (LS) Curve

70C1007

Digitrip 520 (I) Curve

70C1008

Digitrip 520 (G) Curve

Courtesy of NationalSwitchgear.com

«
...
23
24
25
26
27
...
»

Содержание Cutler-Hammer Digitrip 520M





































Отзывы:

Нет отзывов

Похожие инструкции для Cutler-Hammer Digitrip 520M

Ulusoy URING12-24-LLC-SF6

Бренд: Eaton Страницы: 26

T8-3-8212/E/HI12

Бренд: Eaton Страницы: 2

Бренд: Block Страницы: 4

Бренд: CHNT Power Страницы: 16

PowlVac ARG 4 Series

Бренд: Powell Страницы: 52

Бренд: Siemens Страницы: 12

3VA25-JP Series

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 18

3VA52-EC.1 Series

Бренд: Siemens Страницы: 12

Бренд: ABB Страницы: 23

DFS F Audio Series

Бренд: Doepke Страницы: 2

Бренд: FEDERAL PACIFIC Страницы: 28

AC-PRO Retrofit Kit

Бренд: Utility Relay Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды