Eaton ATC-900 Скачать руководство пользователя страница 11

Страница: 11 / 50

IB140012EN

For more information visit: www.eaton.com

Instructional Booklet

Effective: March 2021

Page

Operation and Maintenance Manual,
Automatic Transfer Switch Controller, ATC-900

2.6 Specification Summary

Refer to Table 3.

Table 3. ATC-900 Specifications.

Figure 6. Dimensions. Depth of 3.60 inches with DCT module installed.

PARAMETER

SPECIFICATION

Power Isolation Requirements:

• Control power for Source 1, J7-1,2 must be electrically isolated from control power for Source 2, J7-3,4.

• Similar for accessory I/O Module on J1-1,2 and J1-3,4 for S1 and S2 respectively.

Control Power:

• 120 Vac (50/60 Hz)42mA-ac (operating range 65 to 160 Vac) or 24 Vdc (+/- 20%) at 213mA-dc with DCT Module

Power Consumption:

• 20 VA

Environmental Conditions:

Operating Temperature

• -4.0 to 158 F (-20° to 70°C)

Storage Temperature

• -22°F to +176°F (-30°C to +80°C)

Operating Humidity

• up to 90% Relative Humidity (non-condensing)

Enclosure Compatibility:

• NEMA 12 (standard mounting)

• NEMA 4/4X (mounted with gasket between panel and device faceplate)

• NEMA 3R (outdoor)

• UV Resistant ATC-900 Faceplate

System Voltage Application:

• 120 to 600 Vac (50/60 Hz) (single or three phase)

Voltage Measurements:

• Source 1, Source 2 and Load (VAB, VBC, VCA for Three-Phase System)

Voltage Measurement Range:

• 0 to 720 VAC RMS

Voltage Measurement Accuracy:

• ±1%

Frequency Measurements:

• Source 1 and Source 2

Frequency Measurement Range:

• 40 to 80 Hz

Frequency Measurement Accuracy:

• ±0.2 Hz

Applicable Testing:

• UL Recognized Component including the I/O and DCT Modules

• Meets Seismic Requirements of Uniform and California Building Codes

(exceeding requirements of worst case Zone 4 levels) 3rd Quarter 2014

• Complies with UL 991 environmental tests

• Complies with IEC 61000-4-2, 61000-4-3, 61000-4-4, 61000-4-5, 61000-4-6, and 61000-4-11

• Complies with CISPR 11, Class B

• Complies with FCC Part 15, Subpart B, Class A

Front view

Side view

Top view

5.00 (127.0)

3.63 (92.1)

6.72 (170.7)

10.25

(260.4)

.50 (12.7)

2.10 (53.4)

9.31

(236.5)

Содержание ATC-900



















































Результаты поиска

Содержание ATC-900

Отзывы:

Похожие инструкции для ATC-900

Бренды по названию

Популярные бренды

Eaton ATC-900, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание ATC-900

Отзывы:

Похожие инструкции для ATC-900

Бренды по названию

Популярные бренды