Eaton APS6-400 Series страница 34 Скачать руководство пользователя

Страница: 34 / 114

Access Power Solutions Installation Guide (APS6-400 Series)

IPN 997-00012-53B December 2010

Step 2 - Terminate the cabling





Connect only voltage-free switch or relay contacts to Digital Inputs.



Do not exceed the voltage and current limits of the relay contacts.



For wire size and I/O ratings see Specifications on page

Route the cabling through the access hole in the Input/Output cover to the
terminal blocks on the I/O board.

Test the insulation and continuity of the cabling.

Terminate the wires into the push-connect terminals (see following diagram).

Replace the I/O board.



Input/Output (I/O) cover.



I/O board.



Digital input terminals (push-connect type).



Alarm relay (digital output) terminals (push-
connect type).

Step 3 - Replace the cover and secure cables

Replace the Input/Output (I/O) cover.

Use cable ties to secure the cable(s) and prevent strain on the connections.

Содержание APS6-400 Series











































































































Результаты поиска

Содержание APS6-400 Series

Отзывы:

Похожие инструкции для APS6-400 Series

Бренды по названию

Популярные бренды

Eaton APS6-400 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание APS6-400 Series

Отзывы:

Похожие инструкции для APS6-400 Series

Бренды по названию

Популярные бренды