Eaton APS6-400 Series страница 54 Скачать руководство пользователя

Страница: 54 / 114

Access Power Solutions Installation Guide (APS6-400 Series)

IPN 997-00012-53B December 2010

► To enable/disable the audible alarm indicator

Either:



On SC200 go to: Alarms > Alarm Settings > Audible Alarms > Edit.



or on SC100 go to: Menu > Configuration > Audible Alarm.

Or:



In DCTools/Web go to:

Alarms

Alarm Configuration



When Disabled, the audible indicator will still indicate an invalid key press.

SC200 or SC100 Operation Using a PC/Laptop

DCTools

is configuration software for editing a system controller's configuration file (on-line)

and monitoring the operation of Eaton's dc power systems. It is available free from
www.powerquality.eaton.com/downloads.

Using DCTools via USB (SC200 only)

DCTools

can be run on a PC/laptop connected to the SC200's USB port.



DCTools can also be run on a remote PC/laptop connected to the SC200's RS232 serial port (via a

modem) or Ethernet port. For remote PC/laptop connection details see Communications Options
in the System Controller Operation Handbook.

Before you start you will need:



The latest version of

DCTools

available from www.powerquality.eaton.com/downloads.



A PC/laptop with USB port and USB A/B cable (RadioShack 55010997, Jaycar WC7700, or
equivalent).

► To connect a PC/laptop to the SC200:

Download the latest version of

DCTools

from www.powerquality.eaton.com/downloads.

Install

DCTools

on the PC/laptop.

Connect a USB A/B cable from a USB port on the PC/laptop to the USB port on the SC200.



See the diagram on page

for location of the USB port.

DCTools

will now connect to the SC200.



If connection is not successful refer to DCTools Help (press F1) or Troubleshooting on page

For details of the SC200 control and monitoring functions available via

DCTools see

System

Operation in the System Controller Operation Handbook.



For help using DCTools press F1.

Using DCTools via RS232

DCTools

can be run on a PC/laptop connected to the SC200 or SC100's RS232 port.



For remote PC/laptop connection details see Communications Options in the System Controller

Operation Handbook.

Содержание APS6-400 Series











































































































Результаты поиска

Содержание APS6-400 Series

Отзывы:

Похожие инструкции для APS6-400 Series

Бренды по названию

Популярные бренды

Eaton APS6-400 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание APS6-400 Series

Отзывы:

Похожие инструкции для APS6-400 Series

Бренды по названию

Популярные бренды