manualshive.com logo in svg

Eaton 72400, Информация по ремонту

Поделиться
Скачать
Eaton 72400 Скачать руководство пользователя страница 17

17

Model 72400

1

Inspect

?

Repair

or

Replace

Defective

Action

Step

Comment

Number

Decision

Solution

Symptom:

Gauges Recommended

Inlet vacuum gauge: 2 bar to 1 bar [30 PSI to 30 inHg]
System pressure gauge: 700 bar [10,000 PSI]
Charge pressure gauge:  0 to 50 bar [0 to 600 PSI]
Case pressure gauge: 0 to 25 bar [0 to 300 PSI]

Pressure Ports
Tee in line to check System
Pressure

Drain Port
Tee in line to check Case
Pressure

Auxiliary Port
Check Charge Pressure

Charge Pump Suction Port
Tee in line to check Inlet Vacuum

Figure 3-1

Explanatory
Diagram

Fault - Logic
Trouble Shooting

This fault - logic trouble shooting guide is a diagnostic aid in
locating transmission problems.

Match the transmission symptoms with the problem statements
and follow the action steps shown in the box diagrams. This will
give expedient aid in correcting minor problems eliminating
unnecessary machine down time.

Following the fault - logic diagrams are diagram action
comments of the action steps shown in the diagrams. Where
applicable, the comment number of the statement appears in
the action block of the diagrams.

Recommended Gauge Locations

Содержание 72400


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды