background image

易仕韦尔

EASYWELL

9

2

In principle, don’t add water from the outlet of fog , please connect the water
pipe to input water.

3

Direct humidification is not allowed, it is required that the pipe at the nozzle of
the fog out let should not be shorter than 1 meter.

4

The outlet of the fog should be 1 meter from the equipment at least, and the total
diameter of the mist vent is not less than the diameter of the mist vent of the
equipment.

5

The equipment is not suitable for long-term use in the environment of high
temperature (≥50℃), high dust, strong magnetism and acid and alkali gas.

6

Water tank cleaning period please according to the actual situation, we
recommend once a month least.

7

Please drain out the water if the machine is out of working for long time.

8

Please don’t dig hole on the cover of the machine directly when install the water
filter.

9

The power supply must be cut off, if the machine stop working over 48 hours,
and the water storage in the tank must be drained out entirely. As if the storage
water stocked too long time, it will become ropy, this will affect the function
of the equipment.

10

The overflow and drain pipes must be connected to the floor drain to avoid

accident caused by leakage.

9. After-sales service

1

1 year warranty for the whole machine.

2

Atomized ceramic wafers, filter and fans are belong to the consumables, it’s not

covered by the warranty. If you need to replace them , please contact us ,we will
supply them to you at cost price. You can also buy them in your own in local.

3

The power supply must be cut off, if the machine stop working over 48 hours,

Содержание EW-030HDA











Отзывы: