Lateral Supports
11”-19.5”W
PNG50176
Lateral Supports
8”-16.5”W
PNG50224
Slide each lateral support onto notch and knob
on the accessories mounting bracket. Tighten
knobs securely.
Slide hip supports onto notch and knob under seat.
Tighten knob securely.
If adding hip supports off-unit, remove plastic plugs from top and
bottom of the seat frame.
Hip Supports
Glider medium-PNG50345
Glider large-PNG50374
Roho
®
Seat
Glider medium-PNG50351
Glider large-PNG50353
Guidance and Manufacturer’s Declaration - Electromagnetic Emissions
The EasyStand Glider is intended for use in the electromagnetic environment specified below. The customer or the user
of the EasyStand Glider should assure that it is used in such an environment.
Emissions Test
RF emissions CISPR 11
Group 1
The EasyStand Glider uses RF energy only for its
internal function. Therefore, its RF emissions are
very low and are not likely to cause any interference
in nearby electronic equipment.
The EasyStand Glider is suitable for use in all estab-
lishments, including domestic establishments and
those directly connected to the public low-voltage
power supply network that supplies buildings used
for domestic purposes.
Compliance
Electromagnetic Environment - Guidance
RF emissions CISPR 11
Class B
Harmonic emissions
IEC 61000-3-2
Class A
Voltage fluctuations/
Flicker emissions
IEC 61000-3-3
Complies
Guidance and Manufacturer’s Declaration - Electromagnetic Immunity
The EasyStand Glider is intended for use in the electromagnetic environment specified below. The customer or the
user of the EasyStand Glider should assure that it is used in such an environment.
Immunity Test
Electrostatic
Discharge (ESD)
IEC 61000-4-2
± 6 kV contact
± 8 kV air
± 6 kV contact
± 8 kV air
Floors should be wood, concrete, or ceramic tile. If
floors are covered with synthetic material, the rela-
tive humidity should be at least 30 %.
Mains power quality should be that of a typical com-
mercial or hospital environment.
IEC 60601
Test Level
Electromagnetic Environment - Guidance
Electrical Fast
Transient/Burst
IEC 61000-4-4
± 2 kV for power
supply lines
± 1 kV for input/
output
lines
Surge
IEC 61000-4-5
± 1 kV line(s) to
line(s)
± 2 kV line(s) to
earth
Compliance
Level
± 2 kV for power
supply lines
± 1 kV for input/
output
lines
± 1 kV line(s) to
line(s)
± 2 kV line(s) to
earth
Mains power quality should be that of a
typical commercial or hospital environment.
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC 61000-4-11
<5 % U
T
(>95 % dip in U
T
)
for 0,5 cycle
40 % U
T
(60 % dip in U
T
)
for 5 cycles
70 % U
T
(30 % dip in U
T
)
for 25 cycles
<5 % U
T
(>95 % dip in U
T
)
for 5 s
<5 % U
T
(>95 % dip in U
T
)
for 0,5 cycle
40 % U
T
(60 % dip in U
T
)
for 5 cycles
70 % U
T
(30 % dip in U
T
)
for 25 cycles
<5 % U
T
(>95 % dip in U
T
)
for 5 s
Mains power quality should be that of a typical
commercial or hospital environment. If the user of
the EasyStand Glider requires continued operation
during power mains interruptions, it is recommended
that the EasyStand Glider be powered from an
uninterruptible power supply or a battery.
Power frequency
(50/60 Hz) magnetic
field
IEC 61000-4-8
3 A/m
3 A/m
Power frequency magnetic fields should be at levels
characteristic of a typical location in a typical
commercial or hospital environment.
NOTE: U
T
is the a.c. mains voltage prior to application of the test level.
Page 13 - Pow’r Up Lift Option
Option Assembly - Page 10
