EASYPRINT Compact 32D Скачать руководство пользователя страница 59

Страница: 59 / 243

DESCRIPTION AND INSTALLATION

25364 Issue 8 March 2018

2-39

The Printer Slaves tab enables the user to:

• Add Printer Slave

• Select a reference name for the printer in the Name field

• Enter the IP address of the printer to be the slave printer

Enable communication to the slave by ticking the tickbox - if left unticked,
the slave setting will remain inactive.

Advanced

It is possible to access a remote database, this allows data such as product
name, barcodes, etc. to be retrieved and used within messages.

Name:

Enter the IP address or host name of the PC or Server where the

database is located.

Port:

Enter the port location at which the ODBC resides (normally 701).

ODBC Active:

Tick or untick the box as appropriate.

Note:

Requires ODBC server software, this is available from Easyprint.

Содержание Compact 32D




















































































































































































































































Результаты поиска

Содержание Compact 32D

Отзывы:

EASYPRINT Compact 32D, Руководство по эксплуатации продукта, Страница: 59 / 243

Результаты поиска

Содержание Compact 32D

Отзывы: