EASYPRINT Compact 32D Скачать руководство пользователя страница 164

Страница: 164 / 243

MAINTENANCE, SERVICE AND FAULT FINDING

4-14

25364 Issue 8 March 2018

Align Small Stepper Motor Gears

Fitting the small stepper motor gears onto the plastic side arm teeth is

crucial to proper printer operation.

Perform this procedure after changing either:

• Any parts of the print head actuator mechanism OR

• The small stepper motor.

To align the gears on the plastic side arm teeth:

(1) Push the side arms towards the inside of the printer until they stop, as

arrows show in the following photo:

(2) As shown in the following photo, loosen the four screws that hold the

small stepper motor bracket on to the printer baseplate:

Note:

In the above photo, the print head has been removed.

Содержание Compact 32D




















































































































































































































































Результаты поиска

Содержание Compact 32D

Отзывы:

EASYPRINT Compact 32D, Руководство по эксплуатации продукта, Страница: 164 / 243

Результаты поиска

Содержание Compact 32D

Отзывы: