EASYPRINT Compact 32D Скачать руководство пользователя страница 42

Страница: 42 / 243

DESCRIPTION AND INSTALLATION

2-22

25364 Issue 8 March 2018

Output Voltage

Compact 32d, 32c and 53c

Pin 9 can be used to provide 5V or 24V with ground on pins 13, 14 or 15.

Note:

Default output voltage is 24V.

Output voltage of the powered contacts is set by JP1 and JP2 on the

connection board, as follows:

JP1 and JP2 Position*

Output Voltage (Pin 9)

Maximum Current

1-2

100mA

2-3

24V

500mA

*Both jumpers must be moved.

Communicator II

Pin 9 provides 5V (max 100mA) and ground is on pins 10, 13, 14 and 15

with the I/O box jumpers fitted in the default position. If the I/O box is

changed from volt free to NPN outputs then pins 11 and 12 can be used for
ground as well.

Содержание Compact 32D




















































































































































































































































Результаты поиска

Содержание Compact 32D

Отзывы:

EASYPRINT Compact 32D, Руководство по эксплуатации продукта, Страница: 42 / 243

Результаты поиска

Содержание Compact 32D

Отзывы: