EASYPRINT Compact 32D Скачать руководство пользователя страница 188

Страница: 188 / 243

MAINTENANCE, SERVICE AND FAULT FINDING

4-38

25364 Issue 8 March 2018

Printer LED Status

The LED indicator on the printer is used to indicate the various states of the

printer. The indicator is either on the front of the printer or in the cassette

handle.

Printer Status

LED Colour

Idle

Blue

Ready

Green

Printer Open

Red

Printing

Green

Ribbon Tensioning

Blue

Zero Adjust

Blue

Park

Blue

Error

Red

Busy

Yellow

Initialising

Red

Retraction

Green

Speed too Low

Yellow

Undefined Status

Yellow

Returning

Green

Heating Print Head

Blue

Waiting for Prompt Input

Blue

Note:

For the specific printer state, refer to the Status Bar at the top of
the screen. See

“STATUS BAR” on page 3-8

Содержание Compact 32D




















































































































































































































































Результаты поиска

Содержание Compact 32D

Отзывы:

EASYPRINT Compact 32D, Руководство по эксплуатации продукта, Страница: 188 / 243

Результаты поиска

Содержание Compact 32D

Отзывы: