EASTMAN Kodak X-Omat 3000 RA PROCESSOR Скачать руководство пользователя страница 69

Страница: 69 / 88

Electrical

5B6331 – 01JUN99

Removing the 3000 BOARD, LCD DISPLAY, and DISPLAY PANEL

Warning

• Dangerous Voltage

• Possible damage from electrostatic discharge.

[1] De-energize the PROCESSOR.

[2] Lift the TOP COVER.

[3] Remove the SHROUD by loosening the 5 SCREWS.

[4] Remove the 5 SCREWS that secure the 3000 BOARD.

[5] Disconnect from the 3000 BOARD:

• P/J3001

• P/J3002

• P/J3003

[6] Remove the 3000 BOARD.

[7] Remove the LCD DISPLAY from the the 3000 BOARD:

(a) Remove the 4 SCREWS.

(b) Disconnect CONNECTORS P/J3004 and P/J3005.

[8] Remove the DISPLAY PANEL from the TOP COVER:

(a) Remove the 3 SCREWS.

(b) Remove the NUT securing the ground wire.

[9] Install a new BOARD and assemble the PROCESSOR.

H150_0067HA

DISPLAY

LCD

4 SCREWS

H150_0067HCA

3 SCREWS

5 SCREWS

SHROUD

5 SCREWS

PANEL

DISPLAY

DISPLAY FAN

TOP COVER

3000 BOARD

Содержание Kodak X-Omat 3000 RA PROCESSOR

























































































Результаты поиска

Содержание Kodak X-Omat 3000 RA PROCESSOR

Отзывы:

Похожие инструкции для Kodak X-Omat 3000 RA PROCESSOR

Бренды по названию

Популярные бренды

EASTMAN Kodak X-Omat 3000 RA PROCESSOR, Настройки

Результаты поиска

Содержание Kodak X-Omat 3000 RA PROCESSOR

Отзывы:

Похожие инструкции для Kodak X-Omat 3000 RA PROCESSOR

Бренды по названию

Популярные бренды