background image

1 4

 -

15

 -

F a u l t s a n d s o l u t i o n s

EC6000

 

F a u l t s a n d s o l u t i o n s

EC6000

 

Err11

Motor 

overload

1: P9-23 is set improperly. 
2: The load is too heavy or 
locked rotor occurs on the motor. 
3: The AC drive model is of too 
small power class.

1: Set it correctly. 
2: Reduce the load and check the motor and 
the mechanical condition. 
3: Select an AC drive of higher power 
class.

Err12

Power input 

phase loss

1: The three-phase power input is 
abnormal. 
2: The drive board is faulty. 
3: The lightening board is faulty. 
4: The main control board is 
faulty.

1: Eliminate external faults. 
2: Seek technical support.
3: Seek technical support.
4: Seek technical support.

Err13

Power output 

phase loss

1: The cable connecting the AC 
drive and the motor is faulty. 
2: The AC drive's three-phase 
outputs are unbalanced when the 
motor is running. 
3: The drive board is faulty. 
4: The module is faulty.

1: Eliminate external faults. 
2: Check whether the motor three-phase 
winding is normal. 
3: Seek technical support.
4: Seek technical support. 

Err14

Module 

overheat

1: The ambient temperature is too 
high. 
2: The air filter is blocked. 
3: The fan is damaged.
4: The thermally sensitive 
resistor of the module is damaged. 
5: The inverter module is damaged. 

1: Lower the ambient temperature. 
2: Clean the air filter. 
3: Replace the damaged fan.
4: Replace the damaged thermally 
sensitive resistor. 
5: Replace the inverter module. 

Err15

Err16

 

External 

equipment 

fault

Communi-

cation 

fault

1: External fault signal is input 
via S.

1: The host computer is in 
abnormal state. 
2: The communication cable is 
faulty. 
3: The communication parameters 
in group PB are set improperly.

1:Reset the operation.

1: Check the cabling of host computer. 
2: Check the communication cabling.
3: Set the communication parameters 
properly.

Err17

Err18

Contactor 

faul

Current 

detection 

fault

1: The drive board and power 
supply are faulty. 
2: The contactor is faulty. 

1: The HALL device is faulty. 
2: The drive board is faulty

.

1: Replace the faulty drive board or 
power supply board. 
2: Replace the faulty contactor.

1: Replace the faulty HALL device. 
2: Replace the faulty drive board.

Err19

Motor 

auto-tuning 

fault

1: The motor parameters are not 
set according to the nameplate. 
2: The motor auto-tuning times 
out.

1: Set the motor parameters according 
to the nameplate properly. 
2: Check the cable connecting the AC 
drive and the motor.

Err20

Encoder 

fault

 

1: The encoder type is incorrect. 
2: The cable connection of the 
encoder is incorrect.
3: The encoder is damaged. 
4: The PG card is faulty. 

1: Set the encoder type correctly 
based on the actual situation. 
2: Eliminate external faults.
3: Replace the damaged encoder. 
4: Replace the faulty PG card. 

Err21

Err22

EEPROM 

readwrite 

fault

 

AC drive 

hardware fault

 

1: The EEPROM chip is damaged.

1: Overvoltage exists. 
2: Overcurrent exists.

1: Replace the main control panel.

1: Handle based on over

-

voltage. 

2: Handle based on over

-

current.

Err23

Short circuit 

to ground

1: The motor is short circuited 
to the ground.

1: Replace the cable or motor.

Err24

Err26

EEPORM

 

Initialization

fault

1: Abnormal user data.

1: Reinitialize data and set 
parameters.

Running 

time reached

1: Accumulative running time 
reaches setting.

1: Clear the record through the 
parameter initialization function.

Err29

Power-on time 

reached

Err30

1: Accumulative power-ontime 
reaches the setting.

1: The AC drive running current 
is lower than P9-38

.

1: Clear the record through the 
parameter initialization function.

1: Check the load is disconnected or 
P9-38 and P9-39 is correct.

Load 

becoming 0

Err27

Err28

User-defined 

fault 1

User-defined 

fault 2

1: The user-defined fault 1 signal 
is input via S.

1: Reset the operation.

Err31

Err40

PID feedback 

lost during 

running

Pulse-by-pulse 

current 

limit fault

1: The PID feedback is lower than 
the setting of PA-27.

1: The load is too heavy or 
lockedrotor occurs on the motor. 
2: The AC drive model is of too 
small power class.

1: Check the PID feedback signal or 
set PA-27 to a proper value.

1: Reduce the load and check the 
motor and mechanical condition. 
2: Select the AC drive of higher 
power class.

Err42

Err43

Too large 

speed

 

deviation

Motor 

over-speed

1: The encoder parameters are set 
incorrectly. 
2: The motor auto-tuning is not 
performed. 
3: P9-42 and P9-43 are set 
incorrectly.
1: The encoder parameters are set 
incorrectly. 
2: The motor auto-tuning is not 
performed.
3: P9-40 and P9-41 are set 
incorrectly

1: Set the encoder parameters 
properly. 
2: Perform the motor autotuning. 
3: Set F9-69 and F9-70 correctly 
based on the actual situation.

1: Set the encoder parameters 
properly. 
2: Perform the motor auto-tuning. 
3: Set P9-40 and P9-41 correctly 
based on the actual situation.

Err45

Err51

Motor 

overheat

Pole position

detection

failed

1: The cabling of the temperature 
sensor becomes loose. 
2: The motor temperature is too 
high.

1: The deviation between the motor
parameters and the actual value is
too large.

1: Check the temperature sensor 
cabling and eliminate the cabling 
fault. 
2: Lower the carrier frequency or 
adopt other heat radiation measures.

1: Reconfirm whether the motor 
parameters are correct, and focus on 
whether the rated current is set too 
small. 

Содержание EC6000 Series

































Отзывы: