background image

E-flite Sobré 3D Profile Assembly Manual

Note on Lithium Polymer Batteries

Lithium Polymer batteries are significantly more 

volatile than alkaline or Ni-Cd/Ni-MH batteries used 

in RC applications. All manufacturer’s instructions 

and warnings must be followed closely. Mishandling 

of Li-Po batteries can result in fire. Always follow the 

manufacturer’s instructions when disposing of Lithium 

Polymer batteries.

Warning

An RC aircraft is not a toy! If misused, it can cause serious bodily 

harm and damage to property. Fly only in open areas, preferably 

at AMA (Academy of Model Aeronautics) approved flying sites, 

following all instructions included with your radio.
Keep loose items that can get entangled in the propeller away 

from the prop, including loose clothing, or other objects such as 

pencils and screwdrivers. Especially keep your hands away from 

the propeller.

Warranty Period

Horizon Hobby, Inc., (Horizon) warranties that the Products 

purchased (the “Product”) will be free from defects in materials 

and workmanship at the date of purchase by the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser ("Purchaser") 

and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED 

UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE 

PURCHASER. This warranty covers only those Products purchased 

from an authorized Horizon dealer. Third party transactions are 

not covered by this warranty. Proof of purchase is required for 

warranty claims. Further, Horizon reserves the right to change 

or modify this warranty without notice and disclaims all other 

warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR 

REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-

INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER 

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT 

THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF 

THE PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon's sole obligation hereunder  

shall be that Horizon will, at its option, (i) repair or (ii) replace, 

any Product determined by Horizon to be defective. In the event 

of a defect, these are the Purchaser's exclusive remedies. Horizon 

reserves the right to inspect any and all equipment involved in a 

warranty claim. Repair or replacement decisions are at the sole 

discretion of Horizon. This warranty does not cover cosmetic 

damage or damage due to acts of God, accident, misuse, abuse, 

negligence, commercial use, or modification of or to any part 

of the Product. This warranty does not cover damage due to 

improper installation, operation, maintenance, or attempted 

repair by anyone other than Horizon. Return of any goods 

by Purchaser must be approved in writing by Horizon before 

shipment.

Содержание Sobre 3D Profile

































Отзывы: