background image

39

E-flite PT-19 ARF Assembly Manual

DAMAGE LIMITS

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, 

INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS 

OF PROFITS OR PRODUCTION OR COMMERCIAL 

LOSS IN ANY WAY CONNECTED WITH THE 

PRODUCT, WHETHER SUCH CLAIM IS BASED IN 

CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT 

LIABILITY. Further, in no event shall the liability of 

Horizon exceed the individual price of the Product on 

which liability is asserted. As Horizon has no control 

over use, setup, final assembly, modification or misuse, 

no liability shall be assumed nor accepted for any 

resulting damage or injury. By the act of use, setup or 

assembly, the user accepts all resulting liability.

If you as the Purchaser or user are not prepared 

to accept the liability associated with the use of 

this Product, you are advised to return this Product 

immediately in new and unused condition to the place 

of purchase.

Law: These Terms are governed by Illinois law (without 

regard to conflict of law principals).

SAFETY PRECAUTIONS

This is a sophisticated hobby Product and not a toy. 

It must be operated with caution and common sense 

and requires some basic mechanical ability. Failure to 

operate this Product in a safe and responsible manner 

could result in injury or damage to the Product or 

other property. This Product is not intended for use by 

children without direct adult supervision. The Product 

manual contains instructions for safety, operation and 

maintenance. It is essential to read and follow all 

the instructions and warnings in the manual, prior to 

assembly, setup or use, in order to operate correctly 

and avoid damage or injury.

QUESTIONS, ASSISTANCE, AND REPAIRS

Your local hobby store and/or place of purchase 

cannot provide warranty support or repair. Once 

assembly, setup or use of the Product has been 

started, you must contact Horizon directly. This will 

enable Horizon to better answer your questions 

and service you in the event that you may need any 

assistance. For questions or assistance, please direct 

your email to [email protected]

or call 877.504.0233 toll free to speak to a service 

technician.

INSPECTION OR REPAIRS

If this Product needs to be inspected or repaired, 

please call for a Return Merchandise Authorization 

(RMA). Pack the Product securely using a shipping 

carton. Please note that original boxes may be 

included, but are not designed to withstand the rigors 

of shipping without additional protection. Ship via a 

carrier that provides tracking and insurance for lost or 

damaged parcels, as 

Horizon is not responsible for 

merchandise until it arrives and is accepted at our 

facility

. A Service Repair Request is available at www.

horizonhobby.com on the “Support” tab. If you do 

not have internet access, please include a letter with 

your complete name, street address, email address 

and phone number where you can be reached during 

business days, your RMA number, a list of the included 

items, method of payment for any non-warranty 

expenses and a brief summary of the problem. 

Your original sales receipt must also be included for 

warranty consideration. Be sure your name, address, 

and RMA number are clearly written on the outside of 

the shipping carton.

WARRANTY INSPECTION AND REPAIRS

To receive warranty service, you must include your 

original sales receipt

 verifying the proof-of-purchase 

date. Provided warranty conditions have been met, 

your Product will be repaired or replaced free of 

charge. Repair or replacement decisions are at the sole 

discretion of Horizon Hobby.

NON-WARRANTY REPAIRS

Should your repair not be covered by warranty 

the repair will be completed and payment will 

be required without notification or estimate of 

the expense unless the expense exceeds 50% of 

the retail purchase cost.

 By submitting the item for 

repair you are agreeing to payment of the repair 

without notification. Repair estimates are available 

upon request. You must include this request with 

your repair. Non-warranty repair estimates will be 

billed a minimum of ½ hour of labor. In addition you 

will be billed for return freight. Please advise us of 

your preferred method of payment. Horizon accepts 

money orders and cashiers checks, as well as Visa, 

MasterCard, American Express, and Discover cards.

If you choose to pay by credit card, please include 

your credit card number and expiration date. Any 

repair left unpaid or unclaimed after 90 days will 

be considered abandoned and will be disposed of 

accordingly. 

Please note: non-warranty repair is only 

available on electronics and model engines.

Electronics and engines requiring inspection or repair 

should be shipped to the following address:

Horizon Service Center 

4105 Fieldstone Road 

Champaign, Illinois 61822

or

Horizon Hobby UK

Units 1-4, Ployters Road

Staple Tye

Harlow, Essex

CM187NS

United Kingdom

or

Horizon Technischer Service 

Otto-Hahn-Str. 9a 

25337 Elmshorn 

Germany

USA: Please call 1 877 504 0233 or visit 

horizonhobby.com to find our distributor for your 

country for support with any questions or concerns 

regarding this product or warranty.

UK: Please call +44 (0) 1279 641 097 or email 

[email protected] with any questions or 

concerns regarding this product or warranty.

Germany: Please call +49 4121 46199 66 or email 

[email protected] with any questions or 

concerns regarding this product or warranty.

Содержание PT-19 ARF













































Отзывы: