manualshive.com logo in svg

E-FLITE PT-19 ARF, Инструкция по сборке

Поделиться
Скачать
E-FLITE PT-19 ARF Скачать руководство пользователя страница 22

22

E-flite PT-19 ARF Assembly Manual

  10. Use a ruler placed against the stabilizer and 

elevator to align the stabilizer with the elevator.

  11. Align the elevator bellcrank with the center line 

of the fuselage.

  12. Use a #1 Phillips screwdriver and 2mm x 4mm 

machine screw to secure the elevator pushrod in 

the brass pushrod connector.

If you have opted to fly the PT-19 as both a Control 

Line and Radio Control model you will need to 

remove the bellcrank at this time to prepare for 

the elevator servo installation as these two items 

are interchangeable and use the same mount.

Elevator Servo Installation  

RC Option

Required Parts

Elevator servo 

Brass pushrod connector

Fuselage assembly  Connector backplate
4-40 x 1/2-inch socket head screw (4)
#4 washer (4) 

Elevator servo tray

Radio system
2mm x 4mm machine screw

Required Tools and Adhesives

Pin drill 

Drill bit: 1/16-inch (1.5mm)

Pencil 

Thin CA

Pliers 

Phillips screwdriver: #1

Ruler

Hex wrench or ball driver: 3/32-inch

This section details the installation of the elevator 

servo for the radio controlled version of the PT-19. 

If you are building the control line version and 

have installed the elevator bellcrank, please skip 

to the Motor Installation section of the manual. 

Please note the hardware to mount the bellcrank 

platform in the airplane is the same as used to 

mount the elevator servo plate in the airplane.

  1. Use a 3/32 inch hex wrench or ball driver to 

install four 4-40 x 1/2-inch socket head screws 

and four #4 washers to secure the elevator servo 

tray inside the fuselage. Note that the opening for 

the servo faces to the left side of the fuselage.

Содержание PT-19 ARF













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды