background image

EN

F-16 Falcon 80mm EDF

22

Contact Information

Country of Purchase

Horizon Hobby

Contact Information

Address

United States 

of America

Horizon Service Center (Repairs and Repair Requests)

servicecenter.horizonhobby.com/RequestForm/

2904 Research Rd

Champaign, Illinois, 61822 USA

Horizon Product Support (Product Technical Assistance)

[email protected]
877-504-0233

Sales

[email protected]
800-338-4639

European Union

Horizon Technischer Service

[email protected]

Hanskampring 9 

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH

+49 (0) 4121 2655 100

FCC ID: BRWTIARLGTNG1

This equipment complies with FCC and IC radiation exposure limits set forth for 

an uncontrolled environment. This equipment should be installed and operated 

with minimum distance 20cm between the radiator and/or antenna and your body 

(excluding fingers, hands, wrists, ankles and feet). This transmitter must not be co-

located or operating in conjunction with any other antenna or transmitter.

Supplier’s Declaration of Conformity

F-16 Falcon 80mm EDF BNF Basic and PNP (EFL87850/EFL87870)

This device complies with part 15 of the FCC Rules. Operation is subject to 

the following two conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any interference received, 

including interference that may cause undesired operation.

 CAUTION:

 Changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to operate the 

equipment.

NOTE:

 This equipment has been tested and found to comply with the limits for 

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is 

no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to 

try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which 

the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC 

2904 Research Rd.,

Champaign, IL 61822

Email: [email protected]

Web: HorizonHobby.com

FCC Information

IC Information

IC: 6157A-TIARLGTNG1

CAN ICES-3 (B)/NMB-3(B) 

This device contains license-exempt transmitter(s)/receivers(s) that comply with 

Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). 

Operation is subject to the following 2 conditions: 

1. This device may not cause interference.

2. This device must accept any interference, including interference that may 

cause undesired operation of the device.

Compliance Information for the European Union

EU Compliance Statement:

 EFL F-16 Falcon 80mm ARF Plus (EFL87870)

;

 Hereby, Horizon 

Hobby, LLC declares that the device is in compliance with the 

following: EU EMC Directive 2014/30/EU. RoHS 2 Directive 2011/65/

EU, RoHS 3 Directive - Amending 2011/65/EU Annex II 2015/863

EFL F-16 Falcon 80mm BNF Basic (EFL87850)

Hereby, Horizon Hobby, LLC 

declares that the device is in compliance with the following: EU Radio Equipment 

Directive 2014/53/EU, RoHS 2 Directive 2011/65/EU, RoHS 3 Directive - Amending 

2011/65/EU Annex II 2015/863
The full text of the EU declaration of conformity is available at the following internet 

address: https://www.horizonhobby.com/content/support-render-compliance.

Wireless Frequency Range and Wireless Output Power:

2402 – 2478 MHz

19.95dBm

WEEE NOTICE:

This appliance is labeled in accordance with European Directive 

2012/19/EU concerning waste of electrical and electronic equipment 

(WEEE). This label indicates that this product should not be disposed of 

with household waste. It should be deposited at an appropriate facility 

to enable recovery and recycling.

EU Manufacturer of Record:

Horizon Hobby, LLC

2904 Research Road

Champaign, IL 61822 USA

EU Importer of Record:

Horizon Hobby, GmbH

Hanskampring 9

22885 Barsbüttel Germany

Australia/New Zealand:

Содержание F-16 Falcon 80mm EDF
























Отзывы: