E-FLITE BLADE CX2 Скачать руководство пользователя страница 5

Страница: 5 / 48

Non-Warranty Repairs

Should your repair not be covered by warranty the repair will be completed and payment will be

required without notification or estimate of the expense unless the expense exceeds 0% of the retail

purchase cost.

By.submitting.the.item.for.repair.you.are.agreeing.to.payment.of.the.repair.without.notification ..

Repair.estimates.are.available.upon.request ..You.must.include.this.request.with.your.repair ..Non-warranty.repair.

estimates.will.be.billed.a.minimum.of.½.hour.of.labor ..In.addition.you.will.be.billed.for.return.freight ..Please.advise.

us.of.your.preferred.method.of.payment ..Horizon.accepts.money.orders.and.cashiers.checks,.as.well.as.Visa,.

MasterCard,.American.Express,.and.Discover.cards ..If.you.choose.to.pay.by.credit.card,.please.include.your.credit.

card.number.and.expiration.date ..Any.repair.left.unpaid.or.unclaimed.after.90.days.will.be.considered.abandoned.

and.will.be.disposed.of.accordingly ..

Please note: Non-warranty repair is only available on electronics and

model engines.

Electronics.and.engines.requiring.inspection.or.repair.should.be.shipped.to.the.following.address:

Horizon.Service.Center.

4105.Fieldstone.Road.

Champaign,.Illinois.61822

All.other.Products.requiring.warranty.inspection.or.repair.should.be.shipped.to.the.following.address:

Horizon.Product.Support.

4105.Fieldstone.Road.

Champaign,.Illinois.61822

Please call 877-0-0 with any questions or concerns regarding this Product or warranty.

Additional Safety Precautions and Warnings

As.the.user.of.this.product,.you.are.solely.responsible.for.operating.it.in.a.manner.that.does.not.endanger.yourself.

and.others.or.result.in.damage.to.the.product.or.the.property.of.others .

This.model.is.controlled.by.a.radio.signal.that.is.subject.to.interference.from.many.sources.outside.your.control ..

This.interference.can.cause.momentary.loss.of.control.so.it.is.advisable.to.always.keep.a.safe.distance.in.all.

directions.around.your.model,.as.this.margin.will.help.to.avoid.collisions.or.injury .

•. Never.operate.your.model.with.low.transmitter.batteries .

•. Always.operate.your.model.in.an.open.area.away.from.cars,.traffic,.or.people .

•. Avoid.operating.your.model.in.the.street.where.injury.or.damage.can.occur .

•. Never.operate.the.model.out.into.the.street.or.populated.areas.for.any.reason .

•. Carefully.follow.the.directions.and.warnings.for.this.and.any.optional.support.equipment.(chargers,.rechargeable.

battery.packs,.etc .).that.you.use .

•. Keep.all.chemicals,.small.parts.and.anything.electrical.out.of.the.reach.of.children .

•. Moisture.causes.damage.to.electronics ..Avoid.water.exposure.to.all.equipment.not.specifically.designed.and.

protected.for.this.purpose .

•. Never.lick.or.place.any.portion.of.your.model.in.your.mouth.as.it.could.cause.serious.injury.or.even.death .

Содержание BLADE CX2

















































Результаты поиска

Содержание BLADE CX2

Отзывы:

Похожие инструкции для BLADE CX2

Бренды по названию

Популярные бренды

E-FLITE BLADE CX2, Технические характеристики

Результаты поиска

Содержание BLADE CX2

Отзывы:

Похожие инструкции для BLADE CX2

Бренды по названию

Популярные бренды