E-FLITE BLADE CX2 Скачать руководство пользователя страница 12

Страница: 12 / 48

Once.you.have.connected.the.charger.to.a.power.source.(Use.care.to.ensure.proper.polarity.when.connecting.

the.charger.to.the.power.source),.its.red.LED.will.flash.to.indicate.the.charger.has.power.and.is.ready.to.begin.

charging ..Connect.the.Li-Po.battery.pack.to.the.charger.using.the.specially.marked.Balance.Charge.Lead.exiting.

the.battery.pack.and.the.connector.labeled.with.7 .4V.on.the.charger ..The.connector.is.keyed.to.prevent.reverse.

polarity.connection .

Note: Do not force the connector on the Balance Charge Lead into the connector labeled 11.1V on the

charger. Doing so could result in damage to the battery pack and charger, and could result in a fire.

When.the.battery.is.properly.connected.and.charging.normally,.the.red.and.green.LED.indicators.will.glow.solid ..

Once.the.battery.has.been.fully.charged,.the.green.LED.will.go.out,.leaving.just.the.red.LED.glowing.solid ..The.

battery.can.now.be.removed.from.the.charger.and.installed.into.the.Blade™.CX2.for.flight .

Содержание BLADE CX2

















































Результаты поиска

Содержание BLADE CX2

Отзывы:

Похожие инструкции для BLADE CX2

Бренды по названию

Популярные бренды

E-FLITE BLADE CX2, Технические характеристики

Результаты поиска

Содержание BLADE CX2

Отзывы:

Похожие инструкции для BLADE CX2

Бренды по названию

Популярные бренды