E-FLITE BLADE CX2 Скачать руководство пользователя страница 44

Страница: 44 / 48

Replacement Parts List

EFLH1250 . . . . . . . . . . . . . . . . . . . Blade.CX2.RTF.Electric.Coaxial.Heli

EFLB0990 . . . . . . . . . . . . . . . . . . . 7 .4V.800mAh.2-Cell.Li-Po,.JST/Balance

EFLC3110 . . . . . . . . . . . . . . . . . . . 2-3.Cell.Li-Po.Balancing.Charger,.0 .65A

EFLC4000 . . . . . . . . . . . . . . . . . . . AC.to.12VDC,.1 .5.Amp.Power.Supply

EFLH1022 . . . . . . . . . . . . . . . . . . . Bind.Plug:.BCX2

EFLH1024 . . . . . . . . . . . . . . . . . . . 4-in-1.Control.Unit,.Receiver/ESC/Mixer/Gyro.2 .4GHz:.BCX2

EFLH1055 . . . . . . . . . . . . . . . . . . . LP5DSM.5-Channel.Transmitter,.2 .4GHz:.BCX2

EFLH1058 . . . . . . . . . . . . . . . . . . . Transmitter.Antenna,.2 .4GHz:.BCX2

EFLRS60 . . . . . . . . . . . . . . . . . . . . 6 .0-Gram.Super.Sub-Micro.S60.Servo

EFLRS601 . . . . . . . . . . . . . . . . . . . Gear.Set:.S60

EFLRS602 . . . . . . . . . . . . . . . . . . . Case.Set:.S60

EFLRSA100 . . . . . . . . . . . . . . . . . . Standard.Arm.Set,.Fine.Spline:.S60

EFLH1121 . . . . . . . . . . . . . . . . . . . Bearing.2x6x3mm.(2):.BCP,.BCX/2

EFLH1209 . . . . . . . . . . . . . . . . . . . Mounting.Accessories.&.Screwdriver:.BCX/2

EFLH1210 . . . . . . . . . . . . . . . . . . . 180.Motor.w/8T.0 .5M.Pinion.Left:.BCX/2

EFLH1211 . . . . . . . . . . . . . . . . . . . 180.Motor.w/8T.0 .5M.Pinion.Right:.BCX/2

EFLH1213 . . . . . . . . . . . . . . . . . . . Outer.Shaft.&.Main.Gear.Set:.BCX/2

EFLH1214 . . . . . . . . . . . . . . . . . . . Shaft.Retaining.Collar.Set:.BCX/2

EFLH1215 . . . . . . . . . . . . . . . . . . . Bearing.4x6x3mm.(2):.BCX/2

EFLH1216 . . . . . . . . . . . . . . . . . . . Swashplate.Set:.BCX/2

EFLH1217 . . . . . . . . . . . . . . . . . . . Lower.Rotor.Head.&.Linkage.Set:.BCX/2

EFLH1218 . . . . . . . . . . . . . . . . . . . Servo.Pushrod.Set:.BCX/2

EFLH1219 . . . . . . . . . . . . . . . . . . . Stabilizer.Flybar.Set:.BCX/2

EFLH1220 . . . . . . . . . . . . . . . . . . . Lower.Main.Blade.Set.(2.pair):.BCX/2

EFLH1221 . . . . . . . . . . . . . . . . . . . Upper.Main.Blade.Set.(2.pair):.BCX/2

EFLH1222 . . . . . . . . . . . . . . . . . . . Landing.Skid.Set:.BCX/2

EFLH1223 . . . . . . . . . . . . . . . . . . . Battery.Support.Set:.BCX/2

EFLH1225 . . . . . . . . . . . . . . . . . . . Hardware.Set:.BCX/2

EFLH1226 . . . . . . . . . . . . . . . . . . . Body.Mount.Rod.&.Grommet.Set:.BCX/2

EFLH1242 . . . . . . . . . . . . . . . . . . . Inner.Shaft.w/Head/Hub:.BCX/2

EFLH1243 . . . . . . . . . . . . . . . . . . . Inner.Shaft.Main.Gear:.BCX/2

EFLH1254 . . . . . . . . . . . . . . . . . . . Main.Frame.Set:.BCX2

EFLH1255 . . . . . . . . . . . . . . . . . . . Front.Body/Canopy:.BCX2

EFLH1256 . . . . . . . . . . . . . . . . . . . Rear.Body:.BCX2

EFLH1257 . . . . . . . . . . . . . . . . . . . Complete.Body.Set:.BCX2

Optional Parts List

EFLH1205 . . . . . . . . . . . . . . . . . . . Training.Gear.Set:.BCX/2

EFLH1208 . . . . . . . . . . . . . . . . . . . Main.Motor.Heat.Sink:.BCX/2

EFLM1913. . . . . . . . . . . . . . . . . . . Heat.Sink.Compound,.5g

EFLH1227 . . . . . . . . . . . . . . . . . . . Front.Body,.Yellow:.BCX

EFLH1228 . . . . . . . . . . . . . . . . . . . Rear.Body,.Yellow:.BCX

EFLH1229 . . . . . . . . . . . . . . . . . . . Complete.Body.Set,.Yellow:.BCX

EFLH1230 . . . . . . . . . . . . . . . . . . . Front.Body,.Police,.Blue:.BCX/2

EFLH1231 . . . . . . . . . . . . . . . . . . . Rear.Body,.Police,.Blue:.BCX/2

EFLH1232 . . . . . . . . . . . . . . . . . . . Complete.Body.Set,.Police,.Blue:.BCX/2

EFLH1240 . . . . . . . . . . . . . . . . . . . Inner.Shaft.w/Aluminum.Head/Hub:.BCX/2

EFLH1241 . . . . . . . . . . . . . . . . . . . Inner.Shaft.for.Aluminum.Head/Hub:.BCX/2

EFLH1244 . . . . . . . . . . . . . . . . . . . Aluminum.Bearing.Holder.w/Bearing:.BCX/2

EFLH1245 . . . . . . . . . . . . . . . . . . . Aluminum.Lower.Rotor.Head.Set:.BCX/2

EFLH1246 . . . . . . . . . . . . . . . . . . . Aluminum.Swashplate.Set:.BCX/2

EFLH1258 . . . . . . . . . . . . . . . . . . . Front.Body,.Marines.w/o.Decals:.BCX/2

EFLH1259 . . . . . . . . . . . . . . . . . . . Rear.Body,.Marines.w/o.Decals:.BCX/2

EFLH1260 . . . . . . . . . . . . . . . . . . . Complete.Body.Set,.Marines.w/Decals/Gun/Missiles:.BCX/2

EFLH1261 . . . . . . . . . . . . . . . . . . . Decal.Set,.Marines:.BCX/2

EFLH1262 . . . . . . . . . . . . . . . . . . . Gun.and.Missile.Set:.BCX/2
Please.see.your.favorite.retailer.or.visit.our.web.site.(

www.E-fliteRC.com

).to.find.the.latest.in.new.replacement.

and.option.parts.releases.for.your.Blade.CX2 .

Содержание BLADE CX2

















































Результаты поиска

Содержание BLADE CX2

Отзывы:

Бренды по названию

Популярные бренды

E-FLITE BLADE CX2, Технические характеристики

Результаты поиска

Содержание BLADE CX2

Отзывы:

Бренды по названию

Популярные бренды