manualshive.com logo in svg

E-FLITE BLADE CX2, Технические характеристики

Поделиться
Скачать
E-FLITE BLADE CX2 Скачать руководство пользователя страница 34

Gyro Gain Trimmer Pot Description and Adjustment

The.“gain”.trimmer.pot.adjusts.the.gain.setting.value.of.the.piezo.gyro.used.to.aid.in.keeping.the.tail.of.the.

helicopter.straight/on.heading.during.flight .

Gain Trimmer Pot

•. The.gain.value.is.set.too.high.if.the.tail.of.the.helicopter.twitches/bounces.quickly.from.side.to.side.when.in.

hover ..If.this.is.case.for.your.model,.reduce.the.gyro.gain.in.small.increments.until.the.tail.of.the.helicopter.no.

longer.twitches/bounces.from.side.to.side.in.hover .

Turn the gyro gain trimmer pot counterclockwise (-) to decrease gyro gain.

•. The.gain.value.is.set.too.low.when.the.tail.of.the.helicopter.feels.“loose”.during.flight,.requiring.constant.left.and.

right.rudder.inputs.to.maintain.heading.when.in.hover ..If.this.is.the.case.for.your.model,.increase.the.gyro.gain.in.

small.increments.until.few,.if.any,.left.and.right.rudder.inputs.are.required.to.maintain.heading .

Turn the gyro gain trimmer pot clockwise (+) to increase gyro gain.

Note: When adjusting the gyro gain trimmer pot, the changes will take effect without the need to power 

down and re-arm the -in-1 unit. However, please exercise extreme caution when adjusting the gyro 

gain trimmer pot with the model armed to prevent personal injury or damage to the model.

Содержание BLADE CX2

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды