E.F. Johnson Company ATLAS 4500 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 54

background image

A-12

ATLAS 4500 Multimode Station Technical Manual

Controller Board

Appendix A - VHF Circuit Descriptions

• RX Interface
• DSP Interface
• Fan Control
• External Port and Serial Links
• Auxiliary
• Firmware

A.4.1 General Description

The Controller PCB contains the following:

• The main microcontroller IC1 containing CPU, flash, RAM, UARTs, ports etc
• Data  latches
• Serial Flash
• 3.3-V and 5-V linear regulators
• Power on reset IC
• PA,  I/F,  etc
• Control /noise filter for the fan in the PA
• 10 MHz osc det I/P used for 10 MHz ref switch control in the Exciter
• DSP I/F port
• Exciter I/F port
• Receiver I/F port
• Relay  O/P
• LED I/F
• Configuration links

A.4.2 Schematic Description

A.4.2.1 PA Interface

The interface has 14 pins. The PA interface provides 24 V 450 mA and 5 V 10 mA.

It controls the PA by means of the PTT line and the bias line [nominally 4 V at
77°F (25°C)].

The forward power and reverse power detector voltages are transferred to the
controller. The PA copper plate temperature can be read through a single pulse
width modulation line.

During power up, the Controller loads the PA calibration data from the Serial flash
IC on the I2C bus. This bus is also used for initial PA calibration.

«
...
46
47
48
49
50
...
»

Содержание ATLAS 4500























































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 4500

Бренд: Makita Страницы: 64

Бренд: Garland Страницы: 36

Бренд: 4MOMS Страницы: 20

Бренд: Gainsborough Страницы: 2

Бренд: WÄRTSILÄ Страницы: 64

Fast PLUG 500 premium

Бренд: SAGEMCOM Страницы: 2

Бренд: X4-Life Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Yakima Страницы: 8

Бренд: hepco & becker Страницы: 4

Бренд: Cequent Страницы: 9

Бренд: HBX Страницы: 12

Бренд: Hama Страницы: 22

Бренд: Camcar Страницы: 6

Бренд: Ratio Computers Страницы: 16

Бренд: Bioenno Power Страницы: 2

Бренд: Lafferty Страницы: 4

Бренд: A&D Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды