E.F. Johnson Company ATLAS 4500 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 54

background image

1-4

ATLAS 4500 Multimode Station Technical Manual

Regulatory Information

Section 1 - Introduction

Proper operation of this repeater under normal conditions results in user exposure
to RF energy below standard acceptable limits.

• Do not allow the antenna to touch or come in very close proximity with the eyes,

face, or any exposed body parts while the repeater is transmitting.

• Do not operate the transmitter of a stationary radio (base station or marine radio)

when a person is within 17.7 feet (5.4 meters) of the antenna.

• Do not operate the repeater in explosive or flammable atmospheres. The

transmitted repeater energy could trigger blasting caps or cause an explosion.

• Do not operate the repeater without the proper antenna installed.

• Do not allow children to operate transmitter equipped repeater equipment.

1.3.2 FCC Part 15.19 Warning Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that

may cause undesired operation.

1.3.3 FCC Part 15.21 Warning Statement

The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could void
the user’s authority to operate the equipment.

1.3.4 FCC Part 15.105(b) Warning Statement

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

NOTE

The preceding warning list is not intended to include all hazards that may be encountered when

using this repeater.

«
...
12
13
14
15
16
...
»

Содержание ATLAS 4500























































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 4500

Бренд: Panasonic Страницы: 443

Бренд: Samsung Страницы: 133

Бренд: Back View Страницы: 168

BIM-BAM GNS-921

Бренд: e2 elektro Страницы: 2

Бренд: Razor Страницы: 2

RAZORX LONGBOARD

Бренд: Razor Страницы: 16

Бренд: RayTek Страницы: 93

Бренд: Tait Страницы: 46

Бренд: Tait Страницы: 9

Бренд: Tait Страницы: 89

Бренд: Tait Страницы: 20

Бренд: Talkswitch Страницы: 334

Бренд: Tait Страницы: 41

Бренд: Tait Страницы: 149

Бренд: Tait Страницы: 132

Document WorkCentre 450c

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 4

Бренд: BAFANG Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды