E.F. Johnson Company ATLAS 4500 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 54

background image

A-16

ATLAS 4500 Multimode Station Technical Manual

Power Supply

Appendix A - VHF Circuit Descriptions

A.5.2 Schematic Description

The OMAP operates all external interfaces and the three serial communication
devices. It also interfaces with the Controller board through a MCBSP BUS and
UART.

A.6 Power Supply

This section contains information on the following Power Supply components:

• Mains-to-48V PSU
• Filters
• Switch Mode DC-to-DC Convertors

A.6.1 General Description

The base station main power supply contains the following:

• 100 – 240 VAC-to-48 VDC supply
• Mains Filter, 48 V I/P and 3 O/P Filters.
• DC to DC 5.2 V PSU
• DC to DC 13.8 V PSU
• DC to DC 24 V PSU
• Cable and connector to main Controller PCB and PA.
• Shielded case

A.6.2 Schematic Description

A.6.2.1 Mains-to-48V PSU

The base station uses a switch mode power supply 100 – 240 VAC input, 48 V 10.5
A, 500 W output. This has a temperature controlled cooling fan inside.

A.6.2.2 Filters

The General power supply board has an EMI filter of the AC mains (inside PSU)
and filter networks on the 48 V DC O/P for ripple and RFI noise.

«
...
50
51
52
53
54
»

Содержание ATLAS 4500























































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 4500

Бренд: Panasonic Страницы: 132

EASA-PHONE KX-T30810

Бренд: Panasonic Страницы: 16

Бренд: KDS Страницы: 72

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 4

Бренд: Parkside Страницы: 89

Бренд: Parkside Страницы: 28

Бренд: Zamel Страницы: 12

Бренд: YUNEEC Страницы: 6

6130N - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренд: Varta Страницы: 132

McPherson Strut MIR 1G00

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 8

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 8

prodrive SUR 3A00

Бренд: Öhlins Страницы: 4

Бренд: Öhlins Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды