E.F. Johnson Company ATLAS 4500 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 54

background image

ATLAS 4500 Multimode Station Technical Manual

A-15

Audio Logic Board

Appendix A - VHF Circuit Descriptions

The Controller sends serial data on 3 lines to the PA 7 bit attenuator ATN1, ATN2,
ATN3 for SI, CLK, LE pins on the attenuator IC.

The Controller has an input port for the temperature sensor sending a pulse width
modulated signal.

A.4.2.8 Firmware

The Controller flash contains following:

• Gateway operational software to obey command protocol from the DSP. DSP

sends commands to set up RF characteristics, modulation etc.

• PA power control software and temperature sensing. Fan control.
• Debug software to allow control through the PC terminal program.
• Alarm points and monitors alarms and takes corrective action
• Controls interfaces with Exciter for frequency setting and PTT indication
• Controls EEPROM reading and writing from various modules. Allows it to be

controlled from the Debug point initially. Later DSP can select.

• Configuration data, serial number etc. Plug and play system for all modules.

Reads config data from all modules.

• Other operational software.

A.5 Audio Logic Board

A.5.1 General Description

The Audio Logic board is the main controller for the base station.

It sends and receives serial control to the Controller using a defined protocol.

It communicates data with the Ethernet link receiving and sending data to its
network.

The TX data encoding, modulation shaping, RX clock recovery, demodulation etc
is done by the hardware and programming.

The TX modulation data is sent synchronously through the I2SCLK, I2SDAT,
ISFRM lines to the Exciter through the Controller board.

The RX modulation is through 90 MHz IF ports, main and diversity.

«
...
49
50
51
52
53
...
»

Содержание ATLAS 4500























































Отзывы:

Нет отзывов

Похожие инструкции для ATLAS 4500

Бренд: Hamax Страницы: 74

Бренд: QUIETON Страницы: 24

Бренд: Quest Engineering Страницы: 24

Бренд: Nauticam Страницы: 2

Бренд: Samsung Страницы: 21

Бренд: F&F Страницы: 8

Line FP7000 Housing

Бренд: Fantasea Страницы: 5

Бренд: Fantasea Страницы: 5

Бренд: Fancom Страницы: 49

Бренд: FANATEC Страницы: 2

Бренд: Napoleon Страницы: 4

Бренд: NEEWER Страницы: 58

Reference Series

Бренд: OEM Audio Страницы: 29

Бренд: XCM Страницы: 11

Бренд: BabySense Страницы: 76

Бренд: Yeti Страницы: 19

Бренд: veba Страницы: 11

Sprinter Bed System Adventure Wagon Kit

Бренд: FVC Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды