Dynojet 24xLC2 Linx Скачать руководство пользователя

Страница: 19 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Inner Mounting Plate and Flange Bearing Installation

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

INNER MOUNTING PLATE AND FLANGE BEARING INSTALLATION

Use the following instructions to install the inner mounting plate and flange bearing to
both the stationary and movable dynos.

You will need the following parts:

• 32300001

Flange Bearing with Lock Collar (2)

• 36582471

Bolt, 3/8-16 x 1.5", Flange-Hex (2)

• 36711100

Nut, 9/16-12, Hex (8)

• 36923100

Washer, 3/8", Flat (18)

• 36943101

Washer, 9/16", Flat (8)

• 61300024

Inner Mounting Plate, Stationary Dyno

• 61300027

Inner Mounting Plate, Movable Dyno

• DM150-011-004 Nut, 3/8-16, Hex (2)
• DM150-019-012 Bolt, 3/8-16 x 1", Hex (16)

NSTALLING

THE

NNER

OUNTING

LATE

AND

LANGE

EARING

—M

OVABLE

YNO

Place the flange bearing on the threaded studs on the inner plate.

Loosely secure the flange bearing to the inner plate using four 9/16-inch washers
and four 9/16-inch nuts.

Secure the inner mounting plate to the movable dyno using eight 3/8 x 1-inch
bolts and eight 3/8-inch flat washers.

Note:

For above ground installations, use only six 3/8 x 1-inch bolts and



six 3/8-inch flat washers.

Verify the flange bearing on the inner mounting plate is centered on the shaft.
Loosen the bearing nuts and center the bearing if necessary.

Figure 7: Secure the Inner Mounting Plate and Flange Bearing to the Movable Dyno

for in ground

installations only

inner mounting plate

flange bearing

Содержание 24xLC2 Linx





































































Результаты поиска

Содержание 24xLC2 Linx

Отзывы:

Похожие инструкции для 24xLC2 Linx

Бренды по названию

Популярные бренды

Dynojet 24xLC2 Linx, Руководство по установке

Результаты поиска

Содержание 24xLC2 Linx

Отзывы:

Похожие инструкции для 24xLC2 Linx

Бренды по названию

Популярные бренды