Dynojet 24xLC2 Linx Скачать руководство пользователя

Страница: 32 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Pulley Mounting Plates and Outer Bearings Installation

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

Secure the Linx detect sensor tab to the pickup collar using one #8-32 screw.

Note:

Verify the tab is positioned perpendicular to the pickup collar as shown in

Figure 19.

Slide the pickup collar onto the idler shaft. The tab will sit in the sensor window.

Tighten the pickup collar cap screw.

Figure 19: Install the Sensor Tab and Pickup Collar

Place a lower stationary dyno pulley mount (P/N 61300023, stamped 2) under the
idler pulley and loosely secure the mount to the inner plate using five



3/8-16 x 1-inch bolts and five 3/8-inch flat washers (one of the holes in the pulley
mount is not used).

Loosely secure the pulley mount to the idler bearing mounting plate using



five 3/8-16 x 1-inch bolts and five 3/8-inch flat washers.

10 Before tightening these bolts, align the idler with the movable dyno pulley.

With a straight edge on the idler pulley there should be an even gap of about



1/8-inch to the movable dyno pulley.

11 Tighten all the bolts.

Figure 20: Install the Pulley Mount Under the Idler Pulley

sensor tab

idler shaft

pickup collar

cap screw

position tab

perpendicular to
the pickup collar

pulley mount

P/N 61300023

stamped 2

idler bearing plate

Содержание 24xLC2 Linx





































































Результаты поиска

Содержание 24xLC2 Linx

Отзывы:

Похожие инструкции для 24xLC2 Linx

Бренды по названию

Популярные бренды

Dynojet 24xLC2 Linx, Руководство по установке

Результаты поиска

Содержание 24xLC2 Linx

Отзывы:

Похожие инструкции для 24xLC2 Linx

Бренды по названию

Популярные бренды