Dynojet 24xLC2 Linx Скачать руководство пользователя

Страница: 17 / 68

L I N X W I T H A T R A F L E X I N S T A L L A T I O N

Dynojet Logo Panels and Pit Covers

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

EMOVING

THE

OVERS

—I

ROUND

If present, remove the pit covers, runner extension, and support leg.

If present, remove the pit covers.

Remove the two 1/4-20 torx screws securing the runner extension to the runner
assembly. Replace the torx screws.

Remove the two bolts, flat washers, and nuts securing the runner extension to the
support leg and remove the runner extension.

Replace the two torx screws removed from the runner assembly.

Remove the bolt and washer securing the support leg to the floor.

Remove the bolt and washer securing the support leg to the track and remove the
support leg. Replace the bolt and washer.

Note:

For clarity, the 4WD dyno and bridge are not shown.

Figure 5: Remove the Runner Extension and Support Leg

A 547

runner extension

runner assembly

support leg

runner extension

support

leg

track

Содержание 24xLC2 Linx





































































Результаты поиска

Содержание 24xLC2 Linx

Отзывы:

Похожие инструкции для 24xLC2 Linx

Бренды по названию

Популярные бренды

Dynojet 24xLC2 Linx, Руководство по установке

Результаты поиска

Содержание 24xLC2 Linx

Отзывы:

Похожие инструкции для 24xLC2 Linx

Бренды по названию

Популярные бренды