Dynamic Engineering IP-429-II Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 34

background image

Embedded Solutions Page 14

IP429II_BASE_REG1

$02 429 Control Register Port read/write

CONTROL REGISTER 1

DATA BIT

DESCRIPTION

7

/RESET4 reset, 1 = enabled

6

/RESET3

5

/RESET2

4

/RESET1

3

/DBCEN4 1 = force parity, 0 = normal

2

/DBCEN3

1

/DBCEN2

0

/DBCEN1

FIGURE 3

IP-429 CONTROL REGISTER 1 BIT MAP

/DBCENx is used to force Parity to be inserted into the data stream.  This bit is normally
left programmed to 0.  There is another control bit within the -3282 that also controls
Parity along with even or odd sense.  It is recommended to use the 3282 control bit.
Default is 0.

/RESETx is used to reset the 3282 associated with each channel.  The channel should
be reset when the 3282 control register is written to. [write only port].  Default is reset
[0].  1 = normal operation.  Reset should be asserted for 200 nS minimum.

The TX FIFO, bit counters, word counter, gap timers, /DRx, and TXR are affected by
reset assertion.  The Control register is not.

«
...
12
13
14
15
16
...
»

Содержание IP-429-II



































Отзывы:

Нет отзывов

Похожие инструкции для IP-429-II

Бренд: QUAD Страницы: 16

Бренд: Aalborg Страницы: 15

Бренд: Aalborg Страницы: 48

Бренд: Jetline Страницы: 58

Бренд: Lawler Страницы: 4

Бренд: Hama Страницы: 46

Бренд: Galcon Страницы: 35

Бренд: FATEK Страницы: 10

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Tissue-Tek TEC 6

Бренд: Sakura Seiki Страницы: 6

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Бренд: bihl+Wiedemann Страницы: 16

Бренд: National Instruments Страницы: 19

Бренд: Water Worker Страницы: 8

Бренд: YASKAWA Страницы: 360

Бренд: Nanjing Putian Datang Information Electronics Co., Ltd. Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды