background image

W A R N I N G

I M P O R T A N T S A F E T Y I N S T R U C T I O N S A N D G U I D E L I N E S

The DM5 marker is not a toy. Misuse may cause serious injury or death.

Please read, understand and follow the directions in the DM5 owner’s manual.

Eye protection that is designed specifically for paintball and meets ASTM/CE standards must be worn by user 

and persons within range.

Recommend 18 years or older to purchase. Person under 18 must have adult supervision.

Always treat the DM5 marker as if it were loaded and able to fire.

Only use compressed air or nitrogen gas in the DM5 marker. DO NOT USE CO

2

.

Do not exceed 800 psi input pressure.

Ensure all air lines and fittings are tightened and secured before gassing up the DM5.

Always chronograph the DM5 marker before playing paintball.

Never shoot the DM5 marker at velocities in excess of 300 feet per second, 

or at velocities greater than local or national laws allow.

Never look into the barrel or breech area of the DM5 when the marker is switched on and able to fire.

Always fit a barrel blocking device to your DM5 when not in use on the field of play.

The owner’s manual should always accompany the product for reference or in the event of 

resale and new ownership.

Do not point the DM5 marker at anything that you do not intend to shoot.

Do not shoot at people, animals, houses, cars or anything not related to the sport of paintball.

Do not fire the DM5 without the Fuse bolt screwed in completely.

If you read these instructions and do not fully understand them or are unsure of your ability to make 

necessary adjustments properly, call DYE or your local pro shop for help.

Содержание DM5





















Отзывы: