63
Tighten the rear roller bolts only enough to prevent slippage at the front roller. Turn both tread-belt tension adjustment bolts in increments of 1/4 turn
each and inspect for proper tension by walking on the belt at a low speed, making sure the belt does not slip. Keep tensioning the bolts until the belt
stops slipping.
•
If you feel the belt is tight enough, but it still slips, the problem may be a loose Motor drive belt under the front cover.
DO NOT OVERTIGHTEN
– Over tightening will cause belt damage and premature bearing failure.
TREADBELT TRACKING ADJUSTMENT:
The performance of your treadmill is dependent on the frame running on a reasonably level surface. If the frame is not level, the front and back roller
cannot run parallel, and constant belt adjustment may be necessary.
The treadmill is designed to keep the tread-belt reasonably centered while in use. It is normal for some belts to drift near one side while the belt is
running with no one on it. After a few minutes of use, the tread-belt should have a tendency to center itself. If, during use, the belt continues to move
toward one side, adjustments are necessary.
TO SET TREADBELT TRACKING:
A 10 mm Allen wrench is provided to adjust the rear roller. Make tracking adjustments from the
left
side only. Set belt speed at approximately 3 to 5
kph.
Remember, a small adjustment can make a dramatic difference!
Turn the bolt clockwise to move the belt to the right. Turn the bolt only a 1/4 turn and wait a few
minutes for the belt to adjust itself. Continue to make 1/4 rotation turns until the belt stabilizes in
the center of the running deck.
The belt may require periodic tracking adjustment depending on use and walking/running
characteristics. Some users will affect tracking differently. Expect to make adjustments as
required to center the tread-belt. Adjustments will become less of a maintenance concern as the
belt is used. Proper belt tracking is an owner responsibility common with all treadmills.
Содержание AT90E
