DXV AT100 Скачать руководство пользователя страница 4

Страница: 4 / 48

Low Temperature Burns

A low temperature burn may occur when the skin has been in contact for

some time with an object at relatively low temperature (about 104 °F

[40 °C]). Susceptibility to burns also depends on an individual's skin

sensitivity and other factors.

3. This product should be used only as described in this manual. Do not use

attachments that are not recommended by the manufacturer.

4. Never operate this product if it has a damaged cord or plug, if the plug is

loose in the outlet, if it is not working properly, or if it has been dropped or

damaged. Please contact our company for instructions on resolving any of

the above issues.

5. Keep the cord away from heated surfaces. (Example: Panel Heater)
6. Never block the air openings of the product. If lint or hair, etc. is stuck

in the air openings, remove it immediately.

7. Never use while sleeping or feeling drowsy.
8. Never drop or insert any object into any opening or hose.
9. Do not use outdoors or operate where aerosol (spray) products are being

used or where oxygen is being administered.

10. Connect this product to a properly grounded outlet only. See Grounding

Instructions.

11. This product should only be connected to a potable water supply line.

Failure to do so will cause problems in the operation.

12. Do not pull out or insert the power plug with wet hands.
13. Disconnect the power plug periodically and clean it with a dry cloth.

Dust accumulated on the power plug may cause fire.

CAUTION

To reduce the risk of minor injury or property damage:

1. This product should only be connected to a 120 V AC, 60 Hz GFCI-protected

outlet.

2. Be sure to set the dry temperature to "Lo" when the following persons use

the toilet.

(Children, elderly persons, persons with illness, persons with limited mobility,

persons with sensitive skin, persons who are taking medicines that cause

drowsiness, persons who are intoxicated, or persons who are extremely

fatigued.)

* If the dryer is used for a long period of time on a setting higher than "Lo",

the user may risk a low temperature burn. For this reason, our company

recommends setting the dryer temperature to "Lo" during use.

Содержание AT100

















































Результаты поиска

Содержание AT100

Отзывы:

Похожие инструкции для AT100

Бренды по названию

Популярные бренды

DXV AT100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AT100

Отзывы:

Похожие инструкции для AT100

Бренды по названию

Популярные бренды