DXV AT100 Скачать руководство пользователя страница 33

Страница: 33 / 48

Using T

his Pr

oduct

Ins
talling T

his Pr

oduct

How to clean the deodorizing cartridge

1. Disconnect the power plug from the outlet.
2. Remove the seat from the toilet (see page

14).

3. Open the cover that is over the

deodorizing cartridge, which is installed on

the underside of the seat.

4. Remove the deodorizing cartridge.
5. Clean off any dust covering the cartridge

filter using a toothbrush.

Be careful! Do not wash the

deodorizing cartridge or allow it to

become wet!

6. Hold the deodorizing cartridge with

your fingertips and insert it into the

opening, and then replace the cover.

Caution: Insert the deodorizing

cartridge into the opening as shown

in the diagram to the right. (Rounded

corners facing upward.)

7. When the cleaning is complete, reinstall

the toilet seat (see page 37).

CAUTION

The deodorizing fan is installed behind the deodorizer cartridge enclosure.

Please do not place your finger or anything other than the deodorizing

cartridge inside the enclosure.

*Doing so may cause an injury to your finger or equipment failure.

How to Clean the Deodorizing Cartridge

The deodorizing cartridge may perform poorly if covered with dust. If odors are present, clean

or replace the cartridge.

Replacing the deodorizing cartridge

If odors still bother you after cleaning the cartridge filter, the deodorizing cartridge has

expired. Please replace it with a new cartridge. The useful life of the deodorizing cartridge is

approximately seven years under normal use.

* The useful life of the deodorizing cartridge is based on average hours of use by a family of four, two males

and two females.

CAUTION

Deodorizing cartridge

Underside of the toilet seat

Cover of the opening

that contains the

deodorizing cartridge

Please make sure the

cartridge orientation is correct

Cartridge

filter

Содержание AT100

















































Результаты поиска

Содержание AT100

Отзывы:

Похожие инструкции для AT100

Бренды по названию

Популярные бренды

DXV AT100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AT100

Отзывы:

Похожие инструкции для AT100

Бренды по названию

Популярные бренды