DX Engineering DXE-4030VA-1 Скачать руководство пользователя | Manualshive

Страница: 5 / 28

background image

- 4 -

Suggested Parts Not Included

DXE-RADP-3

(

US Patent 7,432,875

) Radial Plate: Made from Laser Cut Stainless Steel with 20

Sets of Stainless Steel Radial Attachment Hardware. The DX Engineering Radial Plate is meant for
those having a vertical antenna and want easy, neat and effective way to connect the essential radial
wires to your antenna system for the highest efficiency and strongest signals.

DXE-SSVC-2P

Stainless Steel V-Clamp. One required for mounting the optional

patented

DXE-

RADP-3

Radial Plate to the antenna mounting pipe of 1" to 2" outside diameter. One required for

mounting the optional

DXE-VFCC-H05A

Vertical Feedline Current Choke.

DXE-VFCC-H05-A - 2/5 kW Vertical Feedline Current Choke for Coaxially Fed 50 Ω HF
Vertical Antennas -

Prevents unwanted RFI by eliminating feedline current and radiation allowing

all power to go to the antenna improving efficiency. Reduces noise or unwanted signals picked-up
by the feedline and overcome a less than optimal ground system The V-Clamp, used to mount the
VFCC, part number

DXE-SSVC-2P,

is not included and must be purchased separately.

RADIAL WIRE KITS

: There are optional DX Engineering Radial Wire Kits available.

DXE-

RADW-500K/BD

contains a 500 foot spool of 14 gauge copper stranded wire with black PVC

insulation, 20 Terminal Lugs and 100 Steel or Biodegradable Lawn Staples. The

DXE-RADW-

1000K/BD

Radial Wire Kit contains a 1,000 foot spool of 14 gauge copper stranded wire with

black PVC insulation, 40 Terminal Lugs and 200 Steel or Biodegradable Lawn Staples.

RADW-

20RT, -32RT

or -

65RT

contain 20 each radial wires with 1/4" terminal attached. These kits come

in 20 Ft, 32 Ft, or 65 Ft lengths.

Tools Required

Two 7/16” wrenches, (one of them should be open-end)
1/2” and 7/16” socket and drive
3/16” and 7/64” Allen wrenches
Medium size screwdriver or 5/16” nut driver for the element clamps
Tape measure
Felt-tip marker

Manual Updates

Every effort is made to supply the latest manual revision with each product. Occasionally a manual
will be updated between the time your DX Engineering product is shipped and when you receive it.
Please check the DX Engineering web site (

www.dxengineering.com

) for the latest revision manual.

«
...
3
4
5
6
7
...
»

Содержание DXE-4030VA-1





























Отзывы:

Нет отзывов

Похожие инструкции для DXE-4030VA-1

Бренд: Marquant Страницы: 16

Бренд: Oricom Страницы: 2

QUEST PRO VQ4800

Бренд: KING Страницы: 20

Бренд: Hama Страницы: 38

Бренд: MFJ Страницы: 3

Бренд: MFJ Страницы: 3

Бренд: MFJ Страницы: 2

I3VHF LOOP ANTENNA

Бренд: Ciro Mazzoni Страницы: 126

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 2

Бренд: RCA Страницы: 3

Бренд: Sarantel Страницы: 4

Sensar HV CC-10HV

Бренд: Winegard Страницы: 16

Бренд: Self-Sat Страницы: 6

Бренд: Televes Страницы: 24

Бренд: Televes Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды