DX Engineering DXE-4030VA-1 Скачать руководство пользователя

Страница: 22 / 28

- 21 -

Feedline Connections

Vertical Feedline Current Choke Connections

The optional

DXE-VFCC-H05-A

Vertical Feedline Current Choke is attached to the feedline using

the

DXE-TCB-FPK

- Feed Point Connection Kit which contains two pre-drilled copper tinned

braids for connection to the vertical antenna system. One braid is 8-1/2" long and the shorter is 7-
1/2" long. Connect the longer 8-1/2" braid from the antenna feedpoint located on the base section
of the antenna to the terminal on the

DXE-VFCC-H05-A

Vertical Feedline Current Choke closest

to the

Red

in "

X Engineering

" on the label as shown in

Figure 15

Connect the other 7-1/2" braid from the terminal on the

DXE-VFCC-H05-A

Vertical Feedline

Current Choke closest to the

Black "

on the label to the closest radial wire bolt on the optional

DXE-RADP-3

Radial Plate as shown in

Figures 15 and 15a

. Route both braided cables as shown.

Note:

Ensure the braided connections do not interfere with the tilting process,

and are not accidentally touching anything that could cause a short.

Figure 15

Your coaxial cable from the radio connects direct to the SO-239 connector on the

DXE-VFCC-

H05A

Vertical Feedline Current Choke.

If there is a wing nut and hardware near the SO-239, they are

spares

for the top two terminals.

DO NOT GROUND

this connection.

Содержание DXE-4030VA-1





























Результаты поиска

Содержание DXE-4030VA-1

Отзывы:

Похожие инструкции для DXE-4030VA-1

Бренды по названию

Популярные бренды

DX Engineering DXE-4030VA-1, Руководство пользователя

Результаты поиска

Содержание DXE-4030VA-1

Отзывы:

Похожие инструкции для DXE-4030VA-1

Бренды по названию

Популярные бренды